Wiring of the 97 paper advance switch



#6

Could anyone tell me in which order I should resolder the red, black and white wires on the 97 paper advance switch. They just broke off while I openned it to show my repairs. I don't have notes on this.

The service manual tell me to check continuity between black and red but I can not find more information.

Thanks for your help.

Arnaud

Edited: 11 Nov 2005, 4:56 p.m.


#7

+-----+
| R | ed
| B | lack
| W | hite
| | +---------------------
| +-+ xxxxxxxxxxxxxxx
| printer daughter board pins
|
|
|
\
\
\----------------------------------


#8

Thanks for your answer but I am looking for the other end of the wires.

I know that when not pressed I should have close circuit between Red and Black so the white wire has to be soldered to the centre of the switch.

One of the other pins seem to be always open circuit and the other close circuit with the centre one when pressed.

Which one is which????

Thanks,


Arnaud

Edited: 12 Nov 2005, 10:48 a.m.


#9

Yes, the service manual does not properly explain the switch wiring.

I can't remember the colours, but I think I can remember what the 3 switch contacts should connect to. Maybe that will help. It's a changeover switch, there is a common tag, a normally-closed tag and a normally open tag. When the button is not pressed, there's continuity between 'common' and 'normally closed'. When it is pressed, there's continuity between 'common' and 'normally open'.

The common tag is electrically connected to logic ground. The -ve side of the battery is also ground

The normally closed tag is electrically connected to one of the pins to the printer PCB, and via that PCB to one of the out-of-paper contacts in the printer.

The normally open tag is electrically connected to one of the flag inputs on the ACT chip (22 pin). I think it's either pin 3 or 4

A bit of work with a continuity tester should tell you which of the 3 pins on the logic board is which, then you can connect them to the right switch pins.


#10

Thanks a lot, that is exactly what I was looking for. Now just a bit of cleaning and soldering to do.

Just for the Archive, GND is Black normally closed connected to OOPS Red. This is indicated in the service manual. White is ACT normally open connected to GND Black when the switch is pressed.

Arnaud

Edited: 13 Nov 2005, 6:56 a.m.


Possibly Related Threads...
Thread Author Replies Views Last Post
  PIL-box w/o IL cable = paper weight Joe Horn 15 1,073 11-26-2013, 01:05 AM
Last Post: Les Wright
  Paper on the errors in HP Calculators vs some older computer processors Les Koller 3 344 08-19-2013, 12:37 PM
Last Post: Mike Morrow
  Request for HP 30b program to switch to ALG-RPN Sujith Abraham 1 180 09-27-2012, 11:00 AM
Last Post: Bruce Bergman
  How does the HP-97 printer paper feed work? Harald 5 397 03-31-2012, 09:31 AM
Last Post: Harald
  HP Printer paper... any worries? Greg Swartz 6 409 02-01-2012, 09:42 AM
Last Post: Greg Swartz
  9120 printer paper Dave Brown Christchurch NZ 5 347 11-30-2011, 01:02 AM
Last Post: David Ramsey
  HP 67, 97, 97+ emulator Olivier De Smet 8 511 11-11-2011, 09:57 AM
Last Post: Israel Otero
  9100 printer paper David Ramsey 2 251 11-07-2011, 06:08 PM
Last Post: David Ramsey
  a tad pricy thermal paper source Duane Hess 7 515 11-07-2011, 12:17 PM
Last Post: Duane Hess
  Advance handbook 15C Michel Beaulieu 7 340 09-30-2011, 08:22 AM
Last Post: Marcus von Cube, Germany

Forum Jump: