Does anyone know how to open a 38G?



#19

Dear All,

Following the message posted by HrastProgrammer some days ago, I decided to try to repair my 38g. Does anyone know how I can open it without damaging it? Many thanks for your help.

Joao


#20

It's very easy. Peel off the plastic keyboard surround. You'll see six heat stakes that hold the front a back halves together. With an appropriately sized twist drill, by hand, shave down the tops of the posts. Pop the + battery contact off the case tab and seperate the front from the back. It's now open.

#21

Since its a 38G, they are cheap on ebay. Just buy another. They usually sell for around $20 plus S&H. Not worth much time unless you want the experience of repair (an experienced repairman would need 20-30 minutes if he had everything ready, many hobbyests would need 1-2 hours, and a complete novice who KNEW what he was doing could spend 2-4 hours and still wind up with a piece of junk). Just a word of warning.

The other fellows advice sounds like it is for the 48G, but there are instructions on how to open a 38G on Colin Crofts website (I don't know the address offhand, but should show up on a websearch)

Actually, you might consider upgrading to an Hp39G+. It has a few more features most importantly, a decent amount of RAM, better stat functions and lots faster (though the 38G wasn't considered slow, like the 48G series). These are often available for $50-60 on ebay also.

For any old timers that don't keep tabs on all the Hp's, the above are algebraic only graphics calculators.


#22

"The other fellows advice" was what the poster asked for, a 38G. The 48G has an aluminum overlay and ten heat stakes :^)


#23

No, I confess, I have never opened a 38G as they have always been Cheap (and well made).

#24

Hi there,

Thank you very much for your help and advice. I have followed Randy's instructions and found the six heat stakes. I'll now work on them!

Have a nice weekend.

Joao

PS: The reason I want to open this one is to learn how to do it. If it goes wrong, it is not too bad as I have another one and I got this one for free!

#25

Dear All,

You may like to know that my 38G is now safe and back to work! The problem was similar to the one described by HrastProgrammer and I am very proud of the result.

Many thanks, especially to Randy and HrastProgrammer!

Joao


#26

OK - I give up! How did you close the 38G?

Best,

--- Les

[http://www.lesbell.com.au]


#27

The case halves have snaps at the top and sides, it stays together fairly well without any further help.

You could use small flat-head screws on two the bottom posts as some 48 methods do for additional strength if desired. A piece of tape along the bottom edge works too if you want quick access and don't want to peel the surround off again to get to screws.

The 38G is the most easily opened saturn hack platform there is. That 30 pin standard memory pad screams for a custom rom.


#28

Thanks, Randy - it was the mention of heat-stakes that made me curious. My wife's HP-18C has a dead column of keys on the alpha keyboard, so I was thinking of trying to fix it - only I've heard horror stories of the machines held together with heat-stakes. . .

Best,

--- Les

[http://www.lesbell.com.au]


#29

A clamshell with problems is pretty much a lost cause. Here's an old thread about 28's but 18/19C's are the same construction: http://www.hpmuseum.org/cgi-sys/cgiwrap/hpmuseum/archv014.cgi?read=71041#71041


#30

That's what I thought, Randy. Oh, well, it was just a notion. . .

Best,

--- Les

[http://www.lesbell.com.au]

#31

I'd like to buy 18C, 19B, and 19BII units with failed keyboards,
if anyone is willing to sell them cheap. I just want working
electronics for the extraction of the ROM code.

I can't afford to spend the money to buy working ones, nor do I
want to destroy them if they're perfectly good. But if the
keyboard has already failed, they're not much good for anything
else.

Also intereseted in the Pioneers for the same reason, though
dumping the ROMs from models other than the 17B, 27S, and 42S
will be quite difficult.

Eric


#32

Eric, I've just spoken to She Who Must Be Obeyed, and she's happy to donate her dying 18C to the cause. Email me a postal address, and next time I'm going past the post office - probably Tuesday or Thursday of next week - I'll pop it in the mail.

Best,

--- Les

[http://www.lesbell.com.au]

#33

You don't mean that!. The 19C is a Sting series, and is relatively easy to take apart non-destructively -- screws on the bottom, there are 3 PCBs inside, keyboard at the top, then processor/logic, finally PSU/printer in the lower case. After removing the screws, you can seperate the case parts, the PSU/printer PCB is connected to the logic PCB by those spring contacts that HP used in all machines at that time.

The machine that's built like a 28 (Clamshell case) is the 19B (and 19BII).


#34

But putting back together a 19C can be a little bit of a problem... getting the stake pins together undamaged is always fun.


#35

But a lot easier than reassembling a 19B (at least if you want the latter to stay together and work).

#36

Hi Joao,

Good work ... I am happy to see that my post motivated a few people to try to fix their calculators :-)


Possibly Related Threads…
Thread Author Replies Views Last Post
  How to open 82162A Thermal Printer Chassis? Ron Fredericks 1 1,209 07-17-2013, 03:58 AM
Last Post: Tony Duell
  any open source HP 10BII emulators? John 15 4,897 06-12-2013, 09:58 AM
Last Post: Kimberly Thompson
  Programming cable for hp-30b -> wp-34s Open letter to Gene Nigel Rowe 37 10,113 08-02-2012, 12:30 AM
Last Post: Guy Dufour
  Where does the 38G fit in? Matt Agajanian 5 1,747 03-10-2012, 01:08 PM
Last Post: Marcus von Cube, Germany
  Is my HP-38G a keepper? Matt Agajanian 10 2,924 03-02-2012, 01:13 AM
Last Post: bill platt
  HP48 open/repair guides back online Han 2 1,345 11-04-2011, 11:15 PM
Last Post: hpnut
  Create empy list on 38g/39g/40g Kiyoshi Akima 4 1,524 10-25-2011, 10:03 AM
Last Post: M. Joury
  An "Open" letter to "DIY" and "Repurposed" calculator projects Ethan Conner 40 9,892 10-21-2011, 04:41 PM
Last Post: Ethan Conner
  HP48 - WHY where were they made so difficult to open up? mr-scorpio 12 3,689 10-01-2011, 02:23 PM
Last Post: Frido Bohn
  Can we make'em like Bill and David? An open RPN? snaggs 23 5,091 09-18-2011, 04:15 PM
Last Post: Hugh Evans

Forum Jump: