82104A card reader magnetic head



#9

I'm trying to repair a 82104a card reader. I measured the two track magnetic head impedance. I used a Fluke 77 multimeter to do that. The instrument read ~51Ohms in one track and ~75Ohms in the other. Can somebody comfirm that? is unusual a magnetic head with diferent impedance in his tracks. Any information is welcomed. Thanks, Carlos.


#10

Did you disconnect the head from the read/write PCB before you measured its resistance? It's possible the sense amplifier chip measures slightly different on the 2 channels.

Otherwise, I can see no reason why the 2 windings of the head would be different. It's possible (although unlikely) you have shorted turns in one winding which would lower the DC resistance.


#11

I measured with the the head disconnected. The measure is the coil resistance without any active circuit connected. If somebody has a 82104a open and can mesure the coil resistance I will confirm (or not) the difference on coils resistance. Thanks


#12

I measured three that I have open. All 6 coils are between 46 and 48 ohms. Meter = Fluke 179 on manual 600 ohm range.

Edited: 8 Aug 2005, 9:49 p.m.


#13

Thanks for answer. The magnetic head has only two coils, one with red and yellow terminals and the other with blue and orange terminals, the black wire is a ground shield for minimize noise. I supouse that one coil is for timing porpouse an the other for data. Please take a impedance measure in the two coils terminals above descripted. Thanks again.


#14

3 each 82104 = 3 heads x 2 windings each = 6 coils. Just as you asked. All the same resistance since my Fluke doesn't have an impedance setting :^)

I have only seen one bad head ever, on a 97. It was open on one winding. I don't know if a 75 ohm winding would cause a problem. It's much more common for the card detect switches to be the issue as they are easily bent while handling.

Edited: 10 Aug 2005, 12:16 a.m.


#15

Thanks Randy. I supouse my 82104A head has some kind of problem because your heads coils has impedance consistent in ~50Ohms.

#16

It's not clock and data. A pulse on one track is a '0', a pulse on the other track is a '1'. I don't know if simulateous pulses on both tracks are used for anything like a byte marker.


#17

If this is rigth the two coils has the same porpouse and then they must have the same impedance. Thanks Tony


Possibly Related Threads...
Thread Author Replies Views Last Post
  Reasonable price for a 41C, Quad Mem, Time, Navigation and Card reader module? Eelco Rouw 10 592 12-12-2013, 01:52 AM
Last Post: Eelco Rouw
  hp-67 card reader problem. Marcel Samek 5 353 12-09-2013, 09:09 PM
Last Post: Paul Berger (Canada)
  HP-97 card reader pinch roller axle davorin 2 237 09-15-2013, 08:47 AM
Last Post: aj04062
  HP-97 Card Reader davorin 3 228 09-13-2013, 04:21 PM
Last Post: Stephan Matthys
  HP-97 Printer Head aj04062 1 184 09-11-2013, 09:18 PM
Last Post: Randy
  HP-97 Printer Head aj04062 0 129 09-10-2013, 09:19 PM
Last Post: aj04062
  HP-97 thermal head movement davorin 6 325 09-08-2013, 03:09 AM
Last Post: davorin
  HP-67 Card Reader Repair Question aj04062 1 184 08-08-2013, 11:15 AM
Last Post: Randy
  Hp-67 card reader: tantalum capacitor identification Ignacio Sánchez 8 446 06-02-2013, 07:26 PM
Last Post: aj04062
  Testing card reader motor for 65 Michae Altmann 2 222 03-17-2013, 09:24 PM
Last Post: Randy

Forum Jump: