Printer repair



#10

I have an 82162A printer that is failing to print a couple of pixels-- any printout has horizontal white lines through it.

Is this something that might be due to a loose contact that could be repaired? Or is it a bum printhead?


#11

Hi, David; are you well?

Both possibilities are valid. I am not completely aware of how is the HP82162A (HPIL standard printer, right?) head connection, but it seems to me it is not too different of the one found in the HP82143A (HP41 standard peripheral printer). The 82143A has a flat circuit connecting the printer head to the mainboard. The connection is achieved by some sort of "metal clippers" that firmly hold the fex edge to the mainboard connector. I used a small piece of nonconductive, ESD "aware" plastic to "produce" a small clearance between the flex circuit and the "clipper" connectors (Gee, I hope yopu can read this and understand... where are the English terms when I most need them?) so I could remove it. I'd guess: (the order does not mean "preference" order or the like)

1 - cold, broken soldering;

2 - bad connection;

3 - broken cooper trail in flex circuit (today this is easy to repair);

If none, maybe (just maybe) either the printer head or one of the drivers (some 8-pin DIP guys closer to the head connector) are bad. I'd not take this last possibility as the most likely to be because you mentioned there are "some" blank horizontal lines. I'd not go for more than one burned driver or head thermal dot (resistor). At least I'd not.

Anyway, other printer experts (or gurus) surely will give you better guidance.

Hope you succeed.

Luiz (Brazil)


#12

Luiz, what you describe mught be called an "anti-static plastic shim".

Cameron


#13

Hi, Cameron;

thanks! Sometimes my "foreign language" vocabulary is simply not enough! I thought about "slice" or "cut", but I was almost sure it would not be "as good as".

Best regards.

Luiz (Brazil)

Edited: 8 Aug 2004, 11:27 a.m.

#14

Luis,

Yes, I'm fine...except for this printer.

I see the area you mention. The flex cable is folded into a shallow "V" and pressed into a connector on the logic board. I inserted a paper shim in the "V" and plugged the flex cable back into the connector, but it didn't make any difference.

I suppose the next step would be to remove the logic board and resolder the connections of the connector that the flex cable plugs into...


#15

... you have another printer, that would be also another way of testing. I'd either guess an HP82143A printer has compatible printing components (head, mechanics, etc.). If you have a component source, like a trashed printer (the only source I can think of), that would be a possible solution. At least for testing and being sure about the cause.

About removing the logic board: to remove the HP82143A logic board there is no need to remove the printing mechanics assembly, just unplug the wires (I cannot help laughing everytime I see the "öut-of-paper sensor" inscription: OOPS) and flex circuit, but I don't know if the 82162A also eases the job. I remember needing to remove about five screws, if not more than that, to release the board. Be aware of the ON/MODE switch lid contacts, they "tend" to be in touch with the logic board because of the (silicon?) grease used to smooth their movement and maintain surface integrity.

Success! I'd like to help some more, but I think this is all I remember.

Best regards.

Luiz (Brazil)

#16

Your printhead is almost certainly bad. Check the resistance of each pixel with an ohm meter. Two pins are tied together (common). The other pins are the dots. Should be around 100 ohms each.


#17

David,

I assume you mean that I can test the resistance at the end of the flex cable, where it plugs into the logic board. Which connectors are the grounds? The outside ones?


#18

The grounds are together at one end. They will have zero ohms of resistance between them. On most flex cables it is obvious that they are connected together.


Possibly Related Threads...
Thread Author Replies Views Last Post
  HP-97 Printer Repair Adventure LHH 9 622 05-17-2012, 03:09 AM
Last Post: LHH
  HP 97 printer repair manual need ZOleg 3 271 01-13-2009, 07:40 PM
Last Post: ZOleg
  HP-19C Printer Repair Atempt Alexander Wassermann 3 301 09-07-2008, 10:42 PM
Last Post: Michael Meyer
  HP-97 Printer repair Karl-Ludwig Butte 7 430 05-06-2008, 03:20 PM
Last Post: Karl-Ludwig Butte
  Thermal Printer Paper for 82143A Printer? Gordon Hamachi 1 255 02-03-2008, 03:05 PM
Last Post: Randy
  HP-97 Printer parts and repair Clark H Lewis 3 256 08-22-2007, 10:23 PM
Last Post: Gerry Schultz
  IR Printer 82240A repair Miki Mihajlovic 5 351 06-19-2004, 09:52 PM
Last Post: Miki Mihajlovic
  82143A Printer repair? steve 8 431 04-08-2003, 06:09 PM
Last Post: David Smith
  Help with 82240B Printer repair william Beitzel 0 132 02-12-2003, 12:39 PM
Last Post: william Beitzel
  Thermal Printer 82143 -Problems to operate the printer- Martin Wahlich 4 341 12-07-2002, 04:01 PM
Last Post: Martin Wahlich

Forum Jump: