screw hp-15c and 10c



#7

I have a hp-15c and a hp-10c. Both were used when I purchased them. Under the 4 feet on the bottom are the 4 screws that hold it together (of course). One model has phillips screws and the other has what looks like star shaped torx screws. Were both types used, or has a previous owner switched the screws? I looked on this site for a picture of the reset hole where a foot would be removed and the screw still in place, but I did not see any. Any help greatly appreciated.


#8

As I know the screws are all philips on the Voyagers (HP-10C, -12C, -15C, -16C) [at least all that I fixed/owned] and there is *no reset hole*. The only reset is to take out the batteries and short the terminals with a coin or a clip.

Best regards,

Nelson


#9

I've never seen anything but phillips in any of the calcs... I can't remember if there were torx screws in the 9114 drive, but I've never seen them in calcs.

Michael


#10

My HP-71 (1BBBB) has torx screws.

#11

Dr. Mikey, your beloved HP71 is infested with Torx (T6)...


#12

D-mn! I knew I used a Torx driver for something... I completely forgot about the 71! Boy. Do I feel stupid....

Did I mention we've had snow here......?

humbly yours.


#13

Then there are those nasty little security Torx screws in some of the classic series chargers. Good luck finding the proper bit for them little buggers.

#14

**vp

#15

Yes,they used black oxide Torx T8's for a short time in the Voyagers. 100% original.

I have a bunch of original HP Phillips heads for the Voyagers in both silver and black as well as black oxide #2x3/8" Phillips sheet metal screws for the bottom cases holes in 41's. Email me if you need any: etron-at-comcast-dot-net.

#16

Thanks for all the input. Randy you're right, the black oxide Torx T8's are exactly what's in the the 15C. I bought it from the original owner and he told me that the feet fell off, but the calc. had never been opened. That was my first voyager. Then when I recently aquired the 10C I noticed the silver phillips screws and got to wondering. After closer examination, Nelson is correct also, that hole under the upper right foot is not a reset button. I don't know what it is, but there is a small hole that looked like a paper clip could be used there to reset the calc. I tried it, but the bottom of the hole is solid.

Thanks Again!


#17

On the early Voyagers, the logic module was a separate from the keyboard. The two were connected with a flexible circuit and an elastomeric connector on the upper right side of the calculator.

The hole you see under the upper right foot is a pin that projects from the front of the case and fits into the back of the case.

There is a molded "dog bone" in the back of the case that applies pressure on the connector. For this reason, these older, original design Voyagers will not function correctly with the back off the unit as the pressure plate for the keyboard connector is gone. You can see the connector and pins on the upper right side in one of Dave's photos here: http://www.hpmuseum.org/10cint.jpg.

FWIW, the easiest way to tell if your Voyager is a one or two board design is the battery connections. If the connectors are symmetrical, as in the photo above, it is an early version two piece. If there is a spring on the left and gold pin on the right, it is a one piece.

Edited: 10 Feb 2004, 7:43 p.m.

#18

I'm sorry, George. Everytime I see the heading on your post, I take it as if you're expressing your extreme dissatisfaction for the two Voyagers.

I just can't help it...

Larry :-)


#19

I thought that subject title might be an attention grabber. Guess it worked. Thanks again for the info.


Possibly Related Threads...
Thread Author Replies Views Last Post
  HP-10C Series Family Photo Max Stone 5 1,632 10-24-2013, 10:31 PM
Last Post: Eddie W. Shore
  10C, 11C, 12C logos on The Auction Site Peter Murphy (Livermore) 0 725 06-14-2013, 11:24 PM
Last Post: Peter Murphy (Livermore)
  HP41 Upper Screw Well Busted Colin Verrilli 6 1,615 07-16-2012, 08:45 PM
Last Post: matt kernal
  Photo of my HP 15c | 15c LE DigiGal 2 1,146 10-12-2011, 12:34 PM
Last Post: DigiGal
  HP 15c LE vs HP-15C dimensions - BOTH ARE HUGE! Joerg Woerner 4 1,489 10-03-2011, 06:53 AM
Last Post: Jim Johnson
  HP 15C and 15C LE not the same dimensions? Derek 16 2,860 09-30-2011, 05:33 PM
Last Post: Derek
  Original 15C Keyboard Test Works With 15C LE!!! DigiGal 5 1,605 09-26-2011, 07:33 PM
Last Post: M. Joury
  Repairing HP 41C screw posts Fouad M. Kaadou 7 1,765 09-25-2011, 08:19 PM
Last Post: Randy
  Fixing the bezel on a 10C Keith Midson 8 1,824 09-03-2011, 05:00 PM
Last Post: Dan W
  [OT] TAS continues to screw sellers Michael de Estrada 28 4,674 03-18-2011, 04:57 PM
Last Post: Michael de Estrada

Forum Jump: