HPILCOM and HP-41 via RS232c



#4

I tested the program. It works in the two ways.
Id est sending and receiving HP-41 programs via HP82164A.
For instance, this one:
LBL'TEST
'TEST OK
AVIEW
RTN
TEST.DAT:
0015C000F50054455354F754455354204F4B7E85C8022DF5

But I had problems to send programs previously saved
with the following configuration:
HP-41 (HP-IL & X-I/O) -> HP82169A HP-IL/HP-IB -> HP82335A HP-IB/PC card.
I used HP softwares & libraries made for the previous card.
All programs were saved under 'program name.BIN'
Thus CONFIG ( is APPEND)
01 LBL "CONFIG"
02 7 E-3
03 LBL 00
04 CF IND X
05 ISG X
06 GTO 00
07 "PAGE DEBUT?"
08 PROMPT
09 GTO IND X
10 LBL 07
11 SF 00
12 SF 01
13 SF 02
14 GTO 06
15 LBL 11
16 SF 01
17 LBL 09
18 SF 00
19 GTO 08
20 LBL 14
21 SF 01
22 LBL 12
23 SF 02
24 SF 03
25 GTO 06
26 LBL 10
27 SF 01
28 GTO 08
29 LBL 15
30 SF 01
31 LBL 13
32 SF 00
33 LBL 08
34 SF 03
35 LBL 06
36 "TAILLE?"
37 PROMPT
38 CLA
39 FIX 0
40 CF 28
41 CF 29
42 ARCL X
43 ASTO X
44 SF 25
45 GTO IND X
46 GTO 06
47 LBL "8"
48 SF 06
49 SF 05
50 LBL "4"
51 SF 07
52 GTO 05
53 LBL "16"
54 SF 06
55 SF 05
56 SF 04
57 LBL 05
58 CLA
59 2,6350741
60 LBL 04
61 FS? IND X
62 "*"
63 FC? IND X
64 "-"
65 FRC
66 10
67 *
68 X0?
69 GTO 04
70 AVIEW
71 END
was saved under 'CONFIG.BIN':
00B6C000F700434F4E46494700171B1C1301A9F39673B181FB50414745
2044454255543F8EAE7308A800A801A802B7000CA8010AA800B9000FA8
010DA802A803B7000BA801B900CF0FA8010EA80009A80307F75441494C
4C453F8E879C00A91CA91D9B739A73A819AE73B700C20FF20038A806A8
05C401F20034A807B651C401F3003136A806A805A804068700121A1613
1510171411000000000005ACF3F27F2AADF3F27F2D690011104264B5D2
7E000000000000CC072DF9
I renamed it 'CONFIG.DAT' and tested it.
I got 'READ ERR' when 'CONFIG, XEQ'INP on HP-41?!
However the codes used are the same, aren't they?
Please advice. Thanks.


#5

hi emmanuel,
i just copied and pasted the DAT stream from your above posting into my text editor. then i removed the six linebreaks to get one long line of hex numbers. then i added a line break at the end of the hex numbers (right after the 2DF9). then i saved it as "CONFIG.DAT" . reading the program back to an HP-41C through HPILCOM was no problem. maybe, you should check two things: 1) there *must* be a line break at the end of the data. 2) no line breaks are allowed in the data.


hope, this helps

cheers, hans


#6

Sehr Hans,
Alles in Ordnung. Schön.
Danke. Grüsse.
Emmanuel

Possibly Related Threads...
Thread Author Replies Views Last Post
  HP-41(CL): The easiest way to transfer FOCAL programs from a Linux PC to the HP-41 Geir Isene 13 709 12-05-2013, 02:40 AM
Last Post: Hans Brueggemann
  HPIL to RS232C ( HP 48GX) NACHO 0 86 11-02-2008, 03:08 PM
Last Post: Nacho
  HPILCOM and the 41 Gerry Schultz 6 303 05-29-2008, 12:44 PM
Last Post: Gerry Schultz
  HPILCOM Jeff Davis 3 194 05-24-2008, 03:16 PM
Last Post: Egan Ford
  Wiring for HPILCOM = HP41 / PC Interfacing Christoph Klug 5 245 01-06-2006, 05:27 PM
Last Post: PeterP
  Anyone want hp 41 to 41 infra-red data transfer? don wallace 38 1,154 09-21-2005, 04:17 PM
Last Post: don wallace
  Chargers for the 82162 thermal printer and the HPIL- rs232c Opotente 1 129 01-11-2001, 07:21 PM
Last Post: Steve (Australia)

Forum Jump: