magnetic strip malfunction



#2

I got a problem with a preloaded strip of the HP67-97 standard pack.
I'm pretty sure the problem is in the card 'cause I tested it with a 67, a 41 and a 97 (all those read without any problem the other strips of the pack). For this reason, instead that looking for a reader's possible issue I've tryed to clean with alcohol the written side of the card.
The result is the same "Eerror" message.......

What are the advices for this issue?
Thank-you a lot


#3

Some of the cards in my standard pack have become unreadable, while most read ok as well as other cards so like you I suspect a problem with the card, however contamination did not seem to be an issue, but rather it would seem the data recorded on the card is damaged or degraded. The only solution I found was to re-enter the program and create a new card, or have someone with a good card create a copy for you. There are listings for the programs in manual for the standard pack.

Edited: 13 Jan 2013, 12:25 p.m.


#4

Thank-you.
To re-enter the program in the same original card I must recreate the missing "corner", what do you suggest for this pourpose, a piece of "scotch" tape?

Edited: 13 Jan 2013, 12:52 p.m.


#5

I suppose that would work but I have never tried, I replaced my card with a "new" blank card, I did not reuse the original card.

#6

I'm not familiar with the HP-67/97, but the HP-41C would ignore the write protect if user flag 14 was set before recording. The HP-67 may have a similar function.

#7

Aurelio, you should check out this little article on repairing pre-recorded cards for the HP-65, 67/97 and 41C.

How to Repair Pre-recorded Cards

I just finished restoring an HP-65, and I've found this method to be helpful on a number of occasions when a prerecorded card didn't work.

I put one piece of scotch tape on one side of the card, then another on the other side so that both adhesive sides touch each other. You can make it easy on yourself by placing the tape on the card and trimming the excess with a razor blade, using the card edge as a guide.

Hope this works for you!

-Dan

#8

There is also a 2000 post that discuss a work around, here is the link

http://www.hpmuseum.org/cgi-sys/cgiwrap/hpmuseum/archv004.cgi?read=6912


#9

Thank-you all for the help.
I'll check today and report the results
Grazie.


Possibly Related Threads...
Thread Author Replies Views Last Post
  HP-97 Printer Malfunction Dan Lewis 17 1,044 11-25-2013, 10:18 AM
Last Post: Thomas Chrapkiewicz
  Question about magnetic cards for the HP-41C Card Reader Namir 2 301 08-15-2012, 12:15 PM
Last Post: Namir
  41CL installation on machine with zebra strip David Ramsey 14 869 12-30-2011, 01:19 PM
Last Post: Monte Dalrymple
  HP 35 Keyboard Malfunction aj04062 1 204 08-07-2011, 11:53 PM
Last Post: John Robinson
  HP 41 magnetic cards giancarlo 9 559 07-29-2011, 11:37 AM
Last Post: M. Joury
  HP-41 + card reader = "Malfunction" ? BobVA 12 750 06-05-2011, 04:35 PM
Last Post: BobVA
  HP65 (card reader) magnetic head Alberto Fenini 0 148 01-10-2011, 12:02 PM
Last Post: Alberto Fenini
  HP65 which magnetic cards ? Alberto Fenini 2 193 10-03-2010, 09:53 AM
Last Post: Thomas Chrapkiewicz
  Labelling HP41/67/97 magnetic cards Dieter 4 348 08-29-2010, 12:54 AM
Last Post: Gerson W. Barbosa
  HP-41 I/O Circuit Strip Stephan Gloor 0 118 09-26-2009, 12:35 PM
Last Post: Stephan Gloor

Forum Jump: