HP 67 Calculator Battery Terminal plus/minus



#2

I have an HP7 that I acquired without a battery pack. I would like to test it to see if it actually works before investing in a new battery pack. Could someone tell me which battery terminal is plus and which is minus relative to the display end of the calculator?

I am assuming that three NiCAD batteries would provide about 3.6V, so I will try powering it at that voltage from a regulated bench supply.

I have a charger with it but it seems to be inoperative. When powered, I can't see DC between any of the three terminals. Is there some sort of an interlock that holds the supply in standby until it is plugged into the calculator ? After reading several warning posts I am reluctant to power the calculator without a battery pack installed.

Thanks,
Steve


#3

Sure,

From this very museum:

http://www.hpmuseum.org/batts/battery.htm

And from the battery POV :

From the plug POV:

Quote:
Output 3.6-4.7 V DC @ 150-190MA calculator, and 4.2 V DC @ 50-60 MA battery charger. (Exact specs vary slightly with charger model but chargers are interchangeable.) A complete recharge takes 14 hours with the calculator on or off. The batteries are low when extra decimal points are displayed.

     +-----------+
| o - o |
| + o |
+-----------+


Looking at the plug, the center terminal is marked negative. The left terminal is marked + and charges the batteries and the right unmarked terminal (also positive) supplies operating power.

EOQ

Etienne


Edited: 30 Apr 2012, 1:28 p.m.


#4

You should be able to test the voltage on your charger when plugged into the wall socket. If you have no voltage on both sides, there is a good chance that the fuse has blown. Check for continuity across the fuse to confirm and then replace it or solder a small wire across it.

#5

Place the calc upside down on the table with the top facing away from you and the bottom nearest to you. This places the card reader away from you and the instruction label nearest you.

[pre]
the top prong is -ve (furthest away from you)
the bottom prong is +ve (nearest to you)


I use a battery pack from radio shack that takes 3 nicad AA batteries. This rules out any bench supply mistakes and clip the leads to the appropriate terminals.

Cheers, Geoff

check out this old museum post. the 45 has the same battery set up as the 67.

hp 45 set up

#6

This from the archives explains how the charger for the HP 67 works.

Dave


#7

Wow, what a great group, thanks everyone for your kind help.
I'll check it out tonight.
Steve

#8

It's possible that there's a break inside one of the wires near the plug that fits into the calculator. I've had that happen on a charger and found the problem by sticking a pin into each side of the wire back from the plug in order to make a contact while testing for DC.


Possibly Related Threads...
Thread Author Replies Views Last Post
  HP Prime print terminal CD Dodds 4 314 12-06-2013, 10:25 PM
Last Post: CD Dodds
  aOT--Battery/battery contact care advice needed Matt Agajanian 0 129 04-24-2012, 07:35 PM
Last Post: Matt Agajanian
  HP-67 Battery door latch Matt Agajanian 23 766 04-13-2012, 01:57 PM
Last Post: Matt Agajanian
  HP classic calculator battery cover tabs Fouad M. Kaadou 0 95 11-07-2011, 04:54 AM
Last Post: Fouad M. Kaadou
  hp 67, battery Sok-khieng Chum Hun 11 384 09-13-2011, 04:00 AM
Last Post: Tony Duell
  HP-67 battery question Csaba Tizedes (Hungary) 3 161 05-05-2011, 06:33 PM
Last Post: sylvandb
  HP-67 battery questions Thomas Okken 2 158 01-08-2011, 02:44 PM
Last Post: Thomas Okken
  HP-67 Battery Pack Robert Hollyer 1 126 04-09-2010, 10:41 PM
Last Post: John Robinson
  HP-67 Battery Pack AlbertTocarLoseggs 5 213 10-15-2009, 01:26 AM
Last Post: sylvandb
  TDS 500K dead battery, pictures of the inside of the card and the battery. Geoff Quickfall 4 272 04-02-2009, 11:23 PM
Last Post: Geoff Quickfall

Forum Jump: