WP34S V3 : STATUS questions



#2

Hello WP34s Team,

Today I finally made the jump to version 3.0. Reading about the new memory management I tried the STATUS command to see the new information available. So now I have some questions and a comment:

1 - What is exactly the first information shown? It says Steps: 531, FL. 2046

2 - Why is there a difference between the steps shown by STATUS and the steps available when I switch to program mode?

STATUS: 531, Program mode: 525.

3 - I think there is something wrong using [arrow down] and [arrow up] while in STATUS: when viewing the information with [arrow down] and after seeing the registers available, the calculator cycles through flags and stack registers only, but when using [arrow up], it cycles through the entire information.

Well that is all for now,

As always, thank you for this magnificent device and regards,

Miguel

Note: I am using revision 2092.


Edited: 29 Dec 2011, 5:48 p.m.


#3

Quote:
1 - What is exactly the first information shown? It says Steps: 531, FL. 2046

Steps of RAM and steps of flash available.
The current work to put more commands in xrom has taken up some space which we hope to reclaim once the commands are moved.


Quote:
2 - Why is there a difference between the steps shown by STATUS and the steps available when I switch to program mode?

STATUS: 531, Program mode: 525.


Marcus will confirm this I'm sure but I think this is due to us reserving a few stack levels that can't be converted to program steps. Without any stack levels, programs cannot execute.


Quote:
3 - I think there is something wrong using [arrow down] and [arrow up] while in STATUS: when viewing the information with [arrow down] and after seeing the registers available, the calculator cycles through flags and stack registers only, but when using [arrow up], it cycles through the entire information.

Seems like you found a bug.


- Pauli


#4

The bug should be fixed.

Pauli is right, there are some return stack levels reserved which cannot be used as program memory. Try the REGS command if you need more steps. :-)

The new XROM stuff is work in progress (and disabled for the flash build in the most recent compile which recovers another page of user flash memory.)


#5

Thank you, Pauli and Marcus.

Very OT : Marcus, I was looking for information about the CE-163 memory module for a SHARP PC-1500 finding a forum with lot of information about these matters and I was gladly surprised seeing you as a frequent contributor...in fluent French!

Wow, Chapeau!

Miguel


#6

Quote:
...in fluent French!

I wish it were as fluent as it might appear. ;-)


Possibly Related Threads…
Thread Author Replies Views Last Post
  [WP-34S] Unfortunate key damage with update to V3 :( svisvanatha 5 3,299 12-10-2013, 11:37 PM
Last Post: Les Bell
  HP Prime battery status Chris Pem10 0 1,282 12-03-2013, 01:07 AM
Last Post: Chris Pem10
  HP-41: CLR & STATUS Geir Isene 0 972 07-01-2013, 03:19 PM
Last Post: Geir Isene
  HPIB Syntax Error at Status command inaki 3 2,359 04-06-2013, 07:57 PM
Last Post: Paul Berger (Canada)
  [WP34S] WP34S firmware on the AT91SAM7L-STK dev kit? jerome ibanes 1 1,247 10-04-2012, 04:59 PM
Last Post: Paul Dale
  41CL V2 with V3 firmware Gerry Schultz 10 3,086 06-26-2012, 05:08 AM
Last Post: Raymond Wiker
  SY-41CL: Hardware Difference Between V2 and V3 Gerry Schultz 2 1,438 05-26-2012, 11:54 AM
Last Post: Monte Dalrymple
  [WP34S] Underlying format of manual.pdf v3.1? Chris Tvergard 12 3,790 05-20-2012, 05:53 PM
Last Post: Chris Tvergard
  HIGH END HPs.. Status Symbols?? John W Kercheval 13 3,775 05-09-2012, 12:55 AM
Last Post: Matt Agajanian
  USB-41 status update: Upgrade available v3.0 Diego Diaz 2 1,452 04-24-2012, 07:50 AM
Last Post: Diego Diaz

Forum Jump: