Repairing HP 41C screw posts



#9

Hello all,

I have a beloved Hp-41CX who eventually suffered the unavoidable fate of its screw posts breaking after years of pressure.
I need help and techniques to solve the problem, please help.

Thanks in advance,

Fouad


#10

Search the archives. Look back many years--early 2000s. Look fr names such as Vieira, Luiz C. (Brazil)

I hope that helps.

Edited: 25 Sept 2011, 9:58 a.m.

#11

http://www.hpmuseum.org/cgi-sys/cgiwrap/hpmuseum/articles.cgi?read=2


#12

Quote:
http://www.hpmuseum.org/cgi-sys/cgiwrap/hpmuseum/articles.cgi?read=2

I wish we could pull that from the archives. Some really bad ideas in there.

1) *Never* use cyanoacrylates for plastic repair on HP's, especially on screw posts. Styrene plastic welding solvent only. Replace 1/4" screws with 3/8" screws on the lower posts. #2 sheet metal screws work okay, tri-lobular plastic screws are best but very hard to find in small quantities. #2 metal screws are available in hobby shops.

2) *Never* use the described method to attach the logic board to keyboard. You might as well just throw it away now if that is your plan.


#13

Hi Randy,

Maybe Dave can let you put red pen glosses on it:-)

It is a probem--propagation of bad ideas.

Maybe an edited version should be entered in the Archives.

#14

I just repaired one replacing the broken post on the CPU end with a metal standoff. I cut off the broken post near the back of the keyboard and threaded the standoff into the remaining hole. I then chucked the standoff in a drill and filed it down to fit the hole in the CPU board, and adjusted the length of the screw on the bottom and the height of the standoff. Result another great working CX. I have also read that others have glued in metal posts using epoxy.

#15

I got great results by slipping a spring over the split post to keep it together and usable. This has the added advantage of being able to slip the coil connector (and spring) off in the future. The glue and wire-wrap method works fine though.


#16

Quote:
I got great results by slipping a spring over the split post to keep it together and usable. This has the added advantage of being able to slip the coil connector (and spring) off in the future. The glue and wire-wrap method works fine though.

While the wire-wrap method works, a card-reader o-ring makes a great clamp while the solvent cures.

That said, I really don't understand all the angst over cracked posts as longer screws (3/8") fix 95% of the issues with lower posts on the 41. We beat this to death, IIRC, back in 2003/4. A cracked post is no big deal if the 1/4" screw is discarded and replaced with 3/8". HP did this as a production change in about 1983 and on all 41's that were received for service.

A post that has sheared off can usually be repaired with little drama if all the pieces are there. Styrene plastic welding solvent puts it back together, leave overnight to cure and a 3/8" screw completes the job.


Possibly Related Threads…
Thread Author Replies Views Last Post
  Repairing HP 65 Michae Altmann 5 2,124 03-15-2013, 04:13 AM
Last Post: Joel Setton (France)
  [41CL] Repairing an image in Flash Monte Dalrymple 0 921 01-24-2013, 07:01 PM
Last Post: Monte Dalrymple
  Book on repairing HP calculators? Dave F 24 6,125 11-23-2012, 06:46 AM
Last Post: Bart (UK)
  HP41 Upper Screw Well Busted Colin Verrilli 6 2,173 07-16-2012, 08:45 PM
Last Post: matt kernal
  HP-25C Repairing aj04062 11 3,267 10-31-2011, 01:11 PM
Last Post: Randy
  Two new blog posts of interest to members of this forum Steve Leibson 8 2,734 09-19-2011, 04:38 PM
Last Post: Mark Hardman
  The week of repairing calculators David Ramsey 6 2,118 08-25-2011, 12:15 PM
Last Post: David Ramsey
  Repairing a cracked Spice case Jeff Kearns 3 1,566 04-20-2011, 07:27 PM
Last Post: Jose Poyan
  [OT] TAS continues to screw sellers Michael de Estrada 28 6,520 03-18-2011, 04:57 PM
Last Post: Michael de Estrada
  Repairing an HP33E with springs Alberto Fenini 0 991 02-26-2011, 09:44 AM
Last Post: Alberto Fenini

Forum Jump: