Opening the HP49g+


Good Day,

Does any know how to open this calculator? My decimal point button has broken off from the skeleton it's attached to and I want to replace the keyboard. The keyboard is on order after a long mission with HP... I've read one needs to drill (4mm bit) through the six heat stakes in the battery compartment but I only see 2 diagonally across from each other, and the two white looking things (rivets?) at the top. Any ideas?

Is the keyboard skeleton just like on cheapy calcs? A simple plastic part?

Thanks in advance :)



I imagine the hardware of the hp 49g+ is quite similar to that of the 50g. The enter key on my 50g went mushy, which is really annoying on an rpn/rpl calc where you're constantly mashing the thing. I asked for advice on this forum to fix the issue and successfully repaired my enter key with some glue and the advice in this thread - . Basically the post under the enter key and some of the other keys had punched clean through the foam backing that goes underneath the keyboard so they weren't getting the rebound that they were designed to. but on to how to open the calc...

To open the 50g up use a suction cup (you might need to moisten it to get maximum grip) to slowly pull the screen cover off, then find a small screwdriver to unscrew the screws behind the screen cover, then pull the two halves of the calculator apart with your hands (this is pretty hard, and will probably take a while.) Be careful not to pull it apart too hard or else you will break the wire that goes to your speaker, which is glued to the back cover of the calc. What I did was pull the speaker off the back cover so I could open the calc fully and lay it open. Then you need to unscrew a bunch of screws that go into the motherboard inside the calc, and use a drill bit to wear away the caps on the heat sticks (is that what they're called, the little plastic things that run through the motherboard to hold everything in position?). Once you've done this properly, you'll be able to separate the motherboard from the front side of the calc case, and access the keyboard.

On the 50g, I think all the keys were attached to a plastic framework thing except for the right and left shift things which are by themselves. The keyboard itself looks quite cheap honestly when you take it apart - the posts behind the keys are TINY.

Hope at least some of this is applicable to the 49g+, or someone else down the road looking to fix their 50g.



The drilling you describe is for the 48S/G series. As HPnewbie described, it is easier for the 49G+/50G. For a photo to see how to remove the screen, see here. There are two screws on the top of the screen. Once these are removed, you can carefully pry the calculator apart. I used plastic levers from what is commonly known as "mobile phone tools" (see this example)

Edited: 23 Sept 2011, 5:58 a.m.

Possibly Related Threads...
Thread Author Replies Views Last Post
  opening hp 15c for repair FORTIN Pascal 4 940 10-12-2013, 10:35 AM
Last Post: FORTIN Pascal
  opening HP 30B Harald 6 985 02-26-2012, 09:07 AM
Last Post: Marcus von Cube, Germany
  Opening a 100LX David Ramsey 4 697 11-29-2011, 12:34 PM
Last Post: Hubert Weikert
  Opening HP41C Alberto Fenini 2 519 01-08-2010, 03:12 AM
Last Post: John Robinson
  Opening a Woodstock external charger? John Garza 9 1,166 11-03-2009, 01:59 AM
Last Post: Katie Wasserman
  HP42S upgrade and opening... pictures ;-) Geoff Quickfall 3 619 10-19-2009, 04:06 AM
Last Post: nacho
  Voyager - opening up - small questions please Mark Edmonds 12 1,463 06-22-2009, 07:49 AM
Last Post: Mike Morrow
  Opening up a 32E brianh 10 1,304 06-26-2007, 09:45 PM
Last Post: Palmer O. Hanson, Jr.
  Opening HP67: you suggest? Olivier TREGER 7 909 12-21-2006, 03:32 AM
Last Post: Olivier TREGER
  opening an HP-71B Hugo 5 750 06-27-2006, 05:37 AM
Last Post: Etienne Victoria

Forum Jump: