WP 34S : [->] command question



I apologize if this has been answered already, but I do not quite understand how [->] works in order to convert temporarily an integer from a base to another. Here are some examples :

In base 2, 11000b :
[->][blue 8] = 30o
[->][blue 16] = 18h , and I do not need to use [h] to do so.
So, What is the combination to get the base 10 conversion?

Now if I switch to base 16, how do I convert to other bases? [->] alone gives the "Eh" value, of course, but trying to use a combination like [f][->] to try to make it work, gets me an error message : "Bad mode error".

What am I doing wrong?



Edited: 26 Aug 2011, 1:00 p.m.


Miguel, the sequence for temporary display in another base is ->, followed by the shift key, followed by the base. As you have already found out, the f shift key is optional.


Thanks a lot Marcus,

Now I get it.




That does not seem to work in hexadecimal mode, based on what the manual says (page 8):

To use [->] in hexadecimal mode, I have to press [f] first then [->]but if I do that:

[f][->] gives a "bad mode error"

What could be the problem there?




This looks like a bug which needs to be fixed by us.

Edit: Found (and fixed) the bug but I need to build and commit it.

Edit again: The issue should be fixed now. In integer mode f, g and -> may be pressed in any order. In a base that takes E as a digit, f must precede ->. A second press of f after -> is not necessary.

Edited: 26 Aug 2011, 3:30 p.m.


Slightly deviates from the manual, pages 57f: after ->, g may be omitted. Defined this way for quite a long time. Sorry.



pages 57f: after ->, g may be omitted

I assume it's still this way and I simply mixed it up in my comments here. Can you check with the latest emulator? I didn't change anything *after* the arrow, just the arrow detection itself which was definitely broken.

Possibly Related Threads...
Thread Author Replies Views Last Post
  [WP-34S] Unfortunate key damage with update to V3 :( svisvanatha 5 1,007 12-10-2013, 11:37 PM
Last Post: Les Bell
  WP-34S (Emulator Program Load/Save) Barry Mead 1 553 12-09-2013, 05:29 PM
Last Post: Marcus von Cube, Germany
  [HP-Prime CAS] "Warning, ^ (Command) Is ambiguous on non square matrices"?? CompSystems 1 722 12-07-2013, 07:15 PM
Last Post: CompSystems
  DIY HP 30b WP 34s serial flash/programming cable Richard Wahl 2 798 12-04-2013, 11:14 AM
Last Post: Barry Mead
  HP Prime - most favorite command bluesun08 2 608 11-12-2013, 11:29 AM
Last Post: bluesun08
  hp prime - command syntax bluesun08 6 934 11-10-2013, 11:57 AM
Last Post: bluesun08
  WP 34S/43 ?'s Richard Berler 3 711 11-10-2013, 02:27 AM
Last Post: Walter B
  My FrankenCulator (wp-34s) FORTIN Pascal 4 735 11-09-2013, 06:18 PM
Last Post: FORTIN Pascal
  WP 34S Owner's Handbook Walter B 5 968 11-09-2013, 05:34 PM
Last Post: Harald
  wp 34s overlay and programming. FORTIN Pascal 6 1,004 11-08-2013, 01:28 PM
Last Post: Nick_S

Forum Jump: