HP 15-C has odd flashing display



#7

Inserted new batteries. Calc only comes on after holding the "on" key for about 5 secs. Display comes up as follows and is flashing. Note that 3 characters look like incomplete zeroes but obviously I can only post them here as complete characters. Note my use of "space" between characters:

"083spacespace0d,088space," Again, all zeroes are partial as if lcd is failing but it was working fine.

While flashing, if I hit other keys, calculator goes off.

Any help to get this old dog (bought in 1985) working again is much appreciated.


#8

Try holding the y^x key down then pressing the ON key. This forces a hardware reset, but doesn't change the content of memory. The content of the display should change, but not necessarily to anything sensible given what you've described.

Then turn it off. With it off, try holding down the minus key while pressing the ON key. That should clear the memory, resulting in a display of "Pr Error".

If that doesn't work, remove the batteries, leave them out for a few days, and try again.

I've never seen a 15C behaving as badly as you describe, so it's possible that it has a hardware fault.


#9

Quote:
I've never seen a 15C behaving as badly as you describe, so it's possible that it has a hardware fault.

I've seen some similar weird behavior trying to come out of
power down recently with a pre 28xx s/n 12c in which I was
probing around. It required removal of the batteries and
short of the electrolytic cap to sort itself out. Not that
the OP was doing the same, but it seems either the NUT or R2D2
can get into a locked up state, perhaps more conventionally via
non fatal ESD.

#10

Thank you for your help and suggestions. Unfortunately, it had no impact. Flashing characters remain exactly the same regardless of what I do including the y^x suggestion. Also, batteries were out for a few days until I got around to replacing them so I doubt that suggestion will work but will try. I had followed ops manual instruction to short battery terminals briefly, but that had no effect either. Someone asked aboout s/n. It is: 2840A87206 with USA printed to left of s/n. How about using a previous cure all before power up/down became so popular--several blows with a hammer?


#11

Quote:
Someone asked aboout s/n. It is: 2840A87206 with USA printed to left of s/n.

That's the package reduced vintage with the former
memory-use only r2d2 integrated in the cpu. I don't
have one here but I'd speculate the external ISA bus
still carries all activity. You could scope it to
see if the cpu is executing bus cycles coming out of
sleep. It should fall back into sleep (after a few
seconds IIRC) where bus activity is quiesced, notably
the bus clocks are idled.

The R2D2 has AFAICT a separate RC oscillator which clocks
the display drive scan. So if you are seeing random junk
on the display it could be the cpu hasn't set the display
registers to a known state coming out of sleep/power-up and
it is just rendering random power up data.

I'd still take a look at the LC oscillator and verify
that is stable. Other issues I've noticed is a stuck
key on the same row as the on key can cause startup
problems (f/g/sto/rcl). Although in that case the
firmware bails on power-up and shouldn't cause the
failure you've described.

Don't discount physical damage in terms of an open
lqfp package to pcb trace. I've seen some marginal
reflow solder jobs on voyagers that I'd never expect
to be associated with the name HP. So it could be
an intermittent (or a contamination short).

Quote:
How about using a previous cure all before power up/down became so popular--several blows with a hammer?

Resist the temptation. If all attempts at resurrection
fail someone will still buy it from you on EEEbay for
a price which will leave you with an incredible story to
tell.

#12

Quote:
Inserted new batteries. Calc only comes on after holding the "on" key for about 5 secs. Display comes up as follows and is flashing. Note that 3 characters look like incomplete zeroes but obviously I can only post them here as complete characters. Note my use of "space" between characters:

"083spacespace0d,088space," Again, all zeroes are partial as if lcd is failing but it was working fine.

While flashing, if I hit other keys, calculator goes off.

Any help to get this old dog (bought in 1985) working again is much appreciated.


If you're still having issues and are up for some investigation
I'd scope the LC oscillator tank. If the clock isn't restarting
reliably when the NUT tries to come out of power down it could
lead to such anomalies.

What might the serial number of this unit be?

Edited: 20 Oct 2010, 12:29 a.m.


Possibly Related Threads…
Thread Author Replies Views Last Post
  WP-34s ISP (flashing cable) again ;( Bernhard 16 6,027 11-01-2013, 05:02 PM
Last Post: Bernhard
  Re: [WP34S] Flashing Issues Les Wright 22 6,218 10-30-2013, 02:16 PM
Last Post: Les Wright
  help flashing a hp30b to a wp34s john mantooth 3 1,728 09-25-2013, 08:58 AM
Last Post: Thomas Chrapkiewicz
  Flashing cable for HP 20 / 30B Stefan Koenig 3 2,044 09-19-2013, 05:53 AM
Last Post: Marcus von Cube, Germany
  USB flashing/Li-po boards patryk 6 2,582 09-08-2013, 12:31 PM
Last Post: patryk
  Help with flashing HP30s John Ioannidis 14 4,470 09-04-2013, 09:37 PM
Last Post: John Ioannidis
  Flashing at HHC2013 Kiyoshi Akima 1 1,186 08-30-2013, 09:12 AM
Last Post: Matt Kernal
  Self-made WP-34s flashing cable? Victor Koechli 6 3,057 08-15-2013, 10:11 AM
Last Post: Les Wright
  wp34s flashing successful at last Glenn Becker 2 1,511 08-04-2013, 04:33 PM
Last Post: Walter B
  trouble flashing wp34s under Linux Glenn Becker 8 2,897 07-23-2013, 02:21 AM
Last Post: Marcus von Cube, Germany

Forum Jump: