16C display problem



#5

Hi All, I have a 16C which had a leaky display, so I bought a 12c of the same vintage (1984) as a display donor. The 12c display was working perfectly, so I swapped out the 16c old display for the new 12c display, and after various attempts I have it working as best I can. However, one segment in one digit refuses to work.

I would have though these displays would be multiplexed, so if one segment doesn't work, then that same segment in all digits would not work. I have counted the number of contact pads for the siplay to be 57, which would not be enough to individually address all 7 segments and decimal point for 10 digits and annunciators etc, so I figure it must be multiplexed.

Can anyone help me to sort out this problem please ?

Thanks
John


#6

Hi;

I have swapped some Voyager´s displays but never had such problem before.

In time: can you take a picture OR indicate which segment is the one refusing to 'lit'?

Sorry not helping the way I would like to...

Thanks and success!

Luiz (Brazil)


#7

Hi Luiz,

I have it working now. I have been doing this with the display and metal surround as one unit. So coming in at an angle to install one edges four clips, then bring down the other edges clips. The results seem very much dependant on how well seated the display zebra strips are. I just kept on re-seating the display unil it worked. It's just a little tricky installing the display on one edge with the metal clips, then do the other edge, but by then then zebra strip on the first edge is not seated correctly.

I realise I could have removed the metal surround, and placed the display flat on the circuit board, then slid the metal surround over and push the clips through the holes. Maybe that's the better way to do it to avoid problems like missing segments.

Cheers,
john


#8

HI;

I use a long sewing needle to seat the zebra stripe correctly. The needle helps aligning it, either from the inside or the outside of the zebra stripe. If you look at the LCD assembly from the extreme edges, you´ll notice small cuts in both sides of the metal frame where the zebra stripes end. This is where I carefully insert the needle and align the zebra stripe accordingly.

I also came to the conclusion that placing the metal frame after the LCD + stripes works better. Unfortunately I had nothing but bad results with the early models with the flex circuit assembly...

Cheers.

Luiz (Brazil)


Edited: 8 June 2010, 8:03 a.m.


Possibly Related Threads...
Thread Author Replies Views Last Post
  Bought a 16C to compensate a little Eelco Rouw 23 1,751 12-07-2013, 01:26 PM
Last Post: Eelco Rouw
  Shiny new 16C! Keith Midson 7 632 10-27-2013, 02:22 AM
Last Post: Keith Midson
  HP-41c display problem Ignacio Sánchez 6 545 09-04-2013, 10:52 AM
Last Post: Ignacio Sánchez Reig
  HP-16C simulator fhub 12 904 06-30-2013, 10:14 PM
Last Post: Robert Prosperi
  Program for HP-16c... Leonid 9 751 06-07-2013, 08:51 PM
Last Post: David Hayden
  HP 11C/12C/15C/16C case Philippe Cairic 4 572 11-06-2012, 06:04 PM
Last Post: Matt Agajanian
  Understanding HP-16C integer division Jimi 18 1,237 10-16-2012, 09:13 PM
Last Post: Eddie W. Shore
  Can the display for a HP32Sii be replaced with the display from another model? Bruce Larrabee 8 743 10-10-2012, 10:05 PM
Last Post: Luiz C. Vieira (Brazil)
  HP41 Display Problem Fouad M. Kaadou 3 369 06-29-2012, 07:46 AM
Last Post: Fouad M. Kaadou
  Sharp PC 1211 display change -- problem overnight -- suggestions? Gene Wright 12 865 05-16-2012, 03:31 AM
Last Post: Bart (UK)

Forum Jump: