HP-97 printer paper feed cam shaft



#9

How are the nylon(?) rollers attached to the shaft? for example, is the nylon roller bonded to the steel, or is it more like a tire that is glued on? Has anyone ever tried replacing them with something?


#10

Hello Ed,
take a look at these pics . I hope this could help you, but if you have any kind of question, please reply here.

Regards

Ignazio


#11

That should be in Geoff's book if it's not already. Are the o-rings the same size as the ones used for the card reader repair?


#12

Hello Michael,
Sure. I would be very happy if Geoff decided to put this procedure on his book. The o-rings are a little bit more large: they are 8 mm (outer diameter) and 2 mm thickness.
I have uploaded some other images here to better describe the procedure.

Thanks.

Ignazio

Edited: 6 Mar 2010, 12:40 p.m.


#13

Hi Ignazio,

Couple questions.

First, are the "supports" embedded within the rubber? It looks like they are.

Second, how did you get the plastic parts that the rubber is molded to off the shaft? Looks like one would need a thin, strong slotted "collar" of some kind to slip behind the part, then press on the steel shaft using an arbor press.

I have found a person who can possibly mold new rubber on if I can get them off the shaft.

Ed


#14

Hi Ed,

I hope I understood your questions.
To the first, yes, the support is embedded on the rubber. Today evening, when at home, I will upload other more detailed images of the cilinder without the rubber, from diffrent view angle.

To the second question, it's very trivial to take apart the cilinder from the shaft. You must push the pin of the shaft against a strong surface, holding the cilinder tightly. I will show the way with a photo as well.

I hope to be helpful, for now.
Take care

Ignazio


#15

That worked worked. Only problem is the spring jumped out. After much searching I finally found it. Believe it or not, it had jumped into the little box I had been putting my little parts i!

I've now sent the wheels off to a person who rebuilds this kind of stuff for turntables and the like. Says he can do it. I'll let you know, probably in a week or two.

Thanks for all your help.

Ed

#16

Quote:
Hello Ed,
take a look at these pics . I hope this could help you, but if you have any kind of question, please reply here.

Regards

Ignazio


Thanks, Ignazio. That helps a lot. Did you put it a lathe to do the mods? How does it work?
Ed


Possibly Related Threads...
Thread Author Replies Views Last Post
  PIL-box w/o IL cable = paper weight Joe Horn 15 2,191 11-26-2013, 01:05 AM
Last Post: Les Wright
  HP-97 Printer Malfunction Dan Lewis 17 2,106 11-25-2013, 10:18 AM
Last Post: Thomas Chrapkiewicz
  HP-97 Printer Troubleshooting aj04062 6 1,068 10-15-2013, 08:45 PM
Last Post: Eric Smith
  HP-97 Printer Head aj04062 1 522 09-11-2013, 09:18 PM
Last Post: Randy
  HP-97 Printer Head aj04062 0 385 09-10-2013, 09:19 PM
Last Post: aj04062
  HP-97 Printer parts davorin 5 909 08-29-2013, 02:10 AM
Last Post: Benoit Maag
  Paper on the errors in HP Calculators vs some older computer processors Les Koller 3 739 08-19-2013, 12:37 PM
Last Post: Mike Morrow
  HP-97 Printer Repair Adventure LHH 9 1,247 05-17-2012, 03:09 AM
Last Post: LHH
  How does the HP-97 printer paper feed work? Harald 5 884 03-31-2012, 09:31 AM
Last Post: Harald
  HP Printer paper... any worries? Greg Swartz 6 859 02-01-2012, 09:42 AM
Last Post: Greg Swartz

Forum Jump: