HP11c - Swapping Internals Between Two



#8

I have a working 11c that looks horrible on the outside. If I bought a nonworking 11c that looked good, how easy would it be to switch the "insides" so that I would have a nice looking, functional calculator built from the two?

Thanks,
Dave


#9

Swapping internals with the heat staked keyboards is do-able. It requires that the keyboard heat stakes are decapitated and then somehow refixed to the new bezel by:

remelting
gluing
small screws

Check out this posting and see the restoration of the aluminum bezel on a 15C in place and the swapping of a dented aluminum bezel with a donor on a 10C:

bezel restorations on a 15C and 10C


#10

Hi Geoff,

Thanks for the info. I may attempt that. My bad 11c looks like it was stored in a corrosive environment at some point and the keyboard background is full of areas of peeling and flaking paint.

I am also interested in your book when it comes out.

Dave

Edited: 24 Feb 2010, 2:11 p.m.

#11

I've done heatstake removal and restoration on several 41c units, by using a small flat screw driver to lift the top off the heat stake, such that you remove the surround only, i.e. it's donut shaped, and not shearing off the whole top. Then to restore, I use a hot glue gun, squirt some glue, lick my finger, then press with my finger. The licking is to speed up the glue cooling, and prevent my finger getting burnt :-)

Cheers,
John


#12

Johns suggestion is excellent.

I have removed the heads of the heat stakes as he describes and then dry assembled the board back and it held remarkably well without and glue application. As of yet I have not glued the system back together but will.

Additionally, because the back plate is screwed together at four points a thin sheet of dense foam cut to cover the circuit board and placed between the board and the calculator back might also relieve the stress on the decapitated heat stakes.

Cheers, Geoff


#13

Hi Geoff,

any news from your book? ETD?

Walter

#14

I carefully removed the molten (donut-shaped) part and after fixing the calc used a soldering iron with a very pointy tip - it looked like new :)


Possibly Related Threads...
Thread Author Replies Views Last Post
  Bllinky's internals Mike (Stgt) 6 739 11-21-2012, 04:02 AM
Last Post: Mike (Stgt)
  O.T. Reading computer internals designnut 1 333 10-13-2011, 11:15 PM
Last Post: David Ramsey
  wanted: high-resolution photo of 50g internals Eric Smith 9 1,134 10-04-2011, 02:08 AM
Last Post: Marcus von Cube, Germany
  Overwriting 41C module internals spb 12 1,127 04-27-2011, 09:52 PM
Last Post: spb
  restoring an HP11C Alberto Fenini 12 1,080 03-14-2011, 09:24 PM
Last Post: Dallas Osborne
  Where are the Internals for the 50g? Jerry Raia 2 383 08-17-2010, 12:06 AM
Last Post: Jerry Raia
  HP11C Dominique Deprez 2 384 07-13-2010, 07:13 PM
Last Post: Vieira, Luiz C. (Brazil)
  Voyager display swapping - any advice ? John Robinson 5 525 05-28-2010, 11:04 AM
Last Post: Vieira, Luiz C. (Brazil)
  removing alluminium bezel (was restoring an HP11C) Alberto Fenini 2 404 05-24-2010, 04:21 PM
Last Post: Alberto Fenini
  restoring an HP11C Alberto Fenini 0 252 05-20-2010, 06:20 AM
Last Post: Alberto Fenini

Forum Jump: