HP-27 Woodstock Thermal Problem


I have been attempting to repair an HP-27 that has the common thermal power on problem. The symptoms are as described in other threads. At power on the display is blank until the ACT eventually "warms up". The HP-27 can then be power cycled and it functions correctly.

I traced the problem to the ACT 1.6KHz clock output that is incorrectly doubled in frequency to 3.2KHz. I made an initial assumption that the ACT might have an internal hold time problem or a race condition. In order to slow the circuitry down, I decreased the VGG supply voltage. No effect on the thermal problem. I then swapped the DC-DC converter zener diode with sequentially lower value zener diodes to decrease all supply voltages. No effect. I individually varied each supply using an external lab power supply. No effect. I tried the suggested grounding solution, in the unlikely event that there was a ground bounce problem. No effect. The VGG supply is somewhat noisy, so I filtered that. No effect. At this point I am stumped by the problem. Other than an internal ACT pre-heater this issue seems unsolvable. The ACT temperature doesn't need to be raised much above ambient in order for the calculator to function correctly so it could be easily warmed up.

Just curious if anyone has identified other solutions to this problem? It would be interesting to have a schematic diagram of the internal ACT circuitry, to understand the source of the problem. I also searched the various retro IC databases in case any old stock of the ACT was still in existence. Couldn't find anything.

The performance of the HP-27 was impressive in that it functioned over an amazingly large voltage range. The lower limit was the point at which the LED display was no longer visible. Other than that, the HP-27 continued to function correctly.



You mentioned lots of things you tried to fix the double speed clocking problem but I don't see that you tried the solution mentioned here, resistively coupling the clock signal to the rest of the circuit.

This worked for me when all else failed that's why I wrote it up.




Thanks for the suggestion. I tried modifying the circuit using a 20K resistor as your article recommends. But the modification didn't solve the clock problem on this HP-27. I still have a 3.2KHz clock at cold start. Maybe I will try some other values of resistors and see if that has any effect. It's difficult for me to theorize why this clock problem occurs given the insensitivity to voltage. That's odd.

The NMOS ACT is marked with HP's logo. It's not marked with an AMI, Mostek, or other IC manufacturer's logo from that timeframe. I am curious if this was an internally designed HP IC.


Possibly Related Threads...
Thread Author Replies Views Last Post
  Usefulness of Woodstock Cs without their C Matt Agajanian 5 736 12-10-2013, 02:05 PM
Last Post: Geoff Quickfall
  HP-97 thermal head movement davorin 6 688 09-08-2013, 03:09 AM
Last Post: davorin
  How to open 82162A Thermal Printer Chassis? Ron Fredericks 1 384 07-17-2013, 03:58 AM
Last Post: Tony Duell
  Woodstock, Classic & Spices for iPhone Matt Agajanian 8 865 07-10-2013, 06:10 PM
Last Post: BShoring
  Update of Emu28 to v1.27 Christoph Giesselink 4 461 05-02-2013, 04:36 AM
Last Post: Mike (Stgt)
  A Woodstock 67 Matt Agajanian 4 547 05-20-2012, 10:57 PM
Last Post: Mike Morrow
  Disassemble Battery Pack 82028B (woodstock) Jacques Karensky 0 307 05-19-2012, 03:39 AM
Last Post: Jacques Karensky
  Woodstock/Spice Keyboard Cleaning Revisited Matt Agajanian 0 297 05-12-2012, 03:43 PM
Last Post: Matt Agajanian
  Woodstock parts compatiability? Russell Dobson 7 727 03-28-2012, 05:35 AM
Last Post: Luiz C. Vieira (Brazil)
  Re: Spares for vintage calculators HP-25, HP-27? McAllan 1 283 03-02-2012, 08:31 AM
Last Post: samo

Forum Jump: