HP-9000 Series 300



#6

I'm looking for info on the HP-9000 Series 300. It's an HP-UX system that was commonly used as instrument controllers. The model that I am working on is an M68k10 based system - part # 98561X. It dates to about 1985. The system powers up and passes the self-test, but there is no boot device.

What type of system disk did these use? How does it connect to the system? (HP-IB ??) What are the part #'s for typical drives?


#7

I used some of the early HP9000 series minis. Yes, the HP-IB interface is used to connect disk drives (and tape drives, and printers...)

Almost any HPIB drive should work, I don't know the part numbers, but when these were released, drives were advancing from washing machine sized 404Mb drives to 5 1/4 full height 1Gb drives (and very quickly too!)

If you can find almost any HPIB drive, and bootable tape, and an HPIB tape drive to suit, you'll be on your way. It may not be too big an ask, I'm sure there are people out there today with perfectly well working HP9000 HPIB based equipment that would be compatible. It's finding a bootable tape that may be difficult...

#8

I have also been curious about these small HP's. I have a Series 9000 model 340 (98571X)I bough at surplus. The serial number starts with 28 so I think it is from 1988. The machine has HP-IB, HP-HIL (not HP-IL!) RS-232 and a coax LAN interface. The keyboard and mouse are connected through the HP-HIL interface. There are RGB coax outputs for video, I used a Sony monitor to check the unit out. The computer runs from ROM firmware, running some type of LAN monitor software. I have no idea what the machine could be used for and have no use for it myself. Anybody got a use for it? I would be interested in software for it or someone else can have it for $50.


#9

There are a couple of BSD-unices available for the HP300 series: OpenBSD (http://www.openbsd.org/) and NetBSD (http://www.netbsd.org/). I've not used these operating systems on the HP300 series, but I've used OpenBSD on both the i386/Sun4c architectures, and it works well.

Have fun!

#10

If I remember correctly, the 340 was a 68030-based machine able to run HP-UX. We usually ran them as diskless machines -- is the "lan monitor software" the bootrom trying to boot HP-UX DUX over the network? I think you should be able to boot it using an HP-IB disk with HP-UX 8.0 or earlier on it.


#11

Interesting idea, I will try hooking a GPIB disk drive to it and see if it tries to read during the boot sequence. My basic problem is I am flying completely blind. Does anyone know where to get the manuals or info on a 340 or the 300 series, for example the internal DIP switch functions??


#12

I can probably dig up the information, since I work where the 300s were produced. I'll see what I can find.


Possibly Related Threads...
Thread Author Replies Views Last Post
  HP-10C Series Family Photo Max Stone 5 1,363 10-24-2013, 10:31 PM
Last Post: Eddie W. Shore
  [HP Prime] Request: re-execute history like CASIO classPAD serie 300/400 CompSystems 1 857 09-03-2013, 02:47 PM
Last Post: CompSystems
  Stuck Omnibook 300 pop-out mouse. Ideas? Gene Wright 5 1,173 07-03-2013, 02:52 PM
Last Post: Bill (Smithville, NJ)
  HP 50g Takes hours to compute a convergent series Matthew Richards 10 1,831 05-14-2013, 03:30 PM
Last Post: Thomas Klemm
  HP Calc Series Mic 3 973 03-21-2013, 01:34 AM
Last Post: Mic
  HP 48G series -> 20 years NACHO 0 570 12-13-2012, 09:40 AM
Last Post: Nacho
  Swiss clones of the HP Voyager series WaltMaken 10 1,698 11-30-2012, 11:40 AM
Last Post: Harald
  HP-48: extract coefficient of power series Thomas Klemm 3 916 10-21-2012, 11:42 PM
Last Post: Han
  Omnibook 300 battery cells Dave Britten 5 1,206 08-15-2012, 11:54 AM
Last Post: Massimo Gnerucci (Italy)
  Best Keyboard of the HP 28/48/49/50 Series Eddie W. Shore 9 1,840 07-12-2012, 07:21 AM
Last Post: Dave Britten

Forum Jump: