HP-15C locks up when certain keys are pressed



#10

Hello,a ll-

I have a 15C that locks up whenever the CHS, 7, 8, 9 or divide by keys are pressed (top row, right half of keys). I inherited this unit, it has the REV D circuit board. It's otherwise functional and in great shape.

Any suggestions or fixes would be welcome - I'd hate to have to shelf this unit.

Thanks


#11

H;

I am not sure about it, but when you mention REV D circuit board, do you mean the revision with a single PCB or the one with the flex circuit board with the LDC and electronics? I cannot remember...

In any case, the keyboard matrix is the same, i.e., left and right half of it share the same columns (5) and each half has its own four rows.

First (maybe silly) question: [ON]/[×] self-test returns O.K.?

Keyboard test ([ON]/[÷]) maybe out of question because the [÷] key seems troubled, but...

I'd check if there is any conductive 'thingy' connecting copper trails of the processor's terminals, mostly in the terminal connected to the common row these keys share.

Hope this helps a bit.

Cheers.

Luiz (Brazil)


#12

Hello, Luiz-

It is the single piece PCBoard. The self test shows no problem. I cannot run a keyboard test.

Is there a way to remove the board from the upper housing? All I see are plastic pegs every centimeter melted over holding the board in place.

Thanks for the suggestions.

Greg Gosian


#13

Quote:
Is there a way to remove the board from the upper housing? All I see are plastic pegs every centimeter melted over holding the board in place.


This is not directly related to your request but I hope it gives you some insight:


http://www.hpmuseum.org/cgi-sys/cgiwrap/hpmuseum/archv016.cgi?read=99306

You can notice I didn't do a good job when resoldering the plastic rivets. I hope you're more skillful than I am :-)

Regards,

Gerson.


#14

Thanks, Gerson

#15

Removing the keyboard will not help, it will only compound your problem. The *only* reason you would need to do that would be to replace the LCD.

You most likely need to replace the keyboard scanner chip, 1LF5 or 1LM2, it depends upon which version hardware you have. You'll find the same part in a similar vintage 12C.

If your 15C is one of the last versions produced, it will have only one IC, in which case you're out of luck as it can only be found in another identical 15C.


#16

Randy-

Thanks for letting me know - I won't try venturing underneath. I have a 1LM1 chip (small square), and 1LQ9 chip (larger, rectangular) accessible.

Any idea which is the one I am looking for and where I can find a replacement?

Thanks for the reply


#17

Ugh, a two chip variant. It should be the small 1LM1 but I don't know for sure, Eric Smith might know.

I've got a bad feeling that the only source is going to be another two chip 15C :(


#18

I was afraid of something like that.

Thanks, everyone, for all of the advice.

Greg


Possibly Related Threads...
Thread Author Replies Views Last Post
  Broken keys on HP Prime? Tarcisi C 0 310 12-10-2013, 05:59 PM
Last Post: Tarcisi C
  HP 50g switching two keys in the user keyboard Sean Freeman 9 879 12-05-2013, 11:44 AM
Last Post: Mark Puscas
  [HP-Prime] off-center [0], ... [9] num keys CompSystems 1 316 10-18-2013, 10:44 PM
Last Post: Han
  HP Prime - Home and CAS keys BruceH 0 230 10-15-2013, 07:19 PM
Last Post: BruceH
  HP Prime Tip: Setting Up User Keys Eddie W. Shore 2 377 09-27-2013, 09:53 PM
Last Post: Eddie W. Shore
  [HP-Prime] Lack of user soft keys Andy B (Australia) 1 304 08-17-2013, 11:00 AM
Last Post: Tim Wessman
  HP prime keys Mic 27 1,578 04-27-2013, 12:25 PM
Last Post: CompSystems
  HP-41C Tall Keys Strange ON Behavior aj04062 3 417 12-02-2012, 06:49 AM
Last Post: aj04062
  HP-41 'Tall Keys'--which ones? Matt Agajanian 17 1,154 06-19-2012, 09:31 AM
Last Post: Ignacio Sánchez
  HP-41CV "tall keys" version Ignacio Sánchez 16 1,116 06-11-2012, 04:59 AM
Last Post: Diego Díaz

Forum Jump: