HP41CV Dead



#6

I have an HP41CV that was stored for about four years with battery left in it. I recently decided to resurrect it but find that I cannot breath any life into it. It was working when stored but is now as dead as an Auk.

I also have another 41 that works fine so I tried swapping bits back and forth to determine which part is faulty. It turns out that everything in it works except the keyboard/display unit.

In other words the problem isn't related to any of the usual things like crook battery contacts, poor contact between the printed circuit boards, etc. It would appear that something on the display/keyboard unit has died in its sleep. Either that or there is something that needs to be reset.

Any ideas will be greatly appreciated.

Cheers, Ron


#7

I had a 41C expire many years ago. I didn't store it with batteries but I did store it in a hand made leather case my Uncle made for it. The leather dyes and chemicals and the humidity in the pouch destroyed the flimsy interface gizmo between the boards. For a while I had it running with a crude solder job but the wires were too big and stiff for the task at hand. Check the board interface for clean contacts and that the coil assembly is not damaged. I can't recall the proper name for the little thing.

also check the mount posts to see that they are not broken. Then the boards won't make contact either.


#8

Thanks for the tip.

Sadly, deterioration of the conductive strip connecting the two boards isn't the problem. I wish it was for I would rapidly solve it with my trusty soldering iron and a few strands of enamelled wire. No; by a process of elimination I have found that whatever the problem is, it is related to the keyboard/display printed circuit board.

I set out to try to awaken it by means of operating the card reader but alas I cannot try that until I fix the confounded drive wheel which I now find has turned to mush. Now where did I put those little O rings?

Anyroad I am still hoping for suggestions.

Cheers, Ron


#9

Maybe a stupid question but how do you open a HP41CV?
My 2-key is playing tricks with me and I want to clean the calculator on the inside. My HP41CV is about 26 years old and still working pretty good until some month ago. The problem is getting worse.
Any suggestions.


#10

Remove the four rubber feet. Be careful when peeling them off, they have two layers. Make sure you get both layers together or they will not stick again. Remove the four phillips screws that appeared under the feet. Lift off the rear cover. On Fullnuts, lift off the logic board and then the battery shield.

Another specific Fullnut issue: Later units have two 0.015" white teflon washers on the lower posts. If your unit has them, don't loose them! They go on top of the logic board.

Cleaning intermittent 41 keys

If you remove the battery/port connection block from the case bottom, be sure to remove the four port covers or modules first. Removing the block with covers in place can tear the thin conductive foil.


Possibly Related Threads...
Thread Author Replies Views Last Post
  hp41cv memory modules tim peterson 10 1,456 11-07-2013, 11:09 PM
Last Post: Garth Wilson
  HP41CV Mike Powell 12 1,471 10-30-2013, 08:17 AM
Last Post: Mike Powell
  HP41CV Bry Sun 11 1,529 10-22-2013, 12:52 PM
Last Post: Geoff Quickfall
  Previously dead WP 34S is resurrected! JayV 2 576 04-18-2013, 12:41 AM
Last Post: Walter B
  Does anyone want dead 82001 battery packs? Michae Altmann 6 874 03-15-2013, 07:32 PM
Last Post: Harald
  Dead 50g after 3 months Chris Smith 13 1,405 03-13-2013, 12:28 PM
Last Post: chris smith
  HP41cv expiriences of a new user Wolfgang 28 2,635 02-13-2013, 08:02 PM
Last Post: Mike Morrow
  More or less dead HP-67 Bernd Ulmann (Germany) 7 948 02-09-2013, 12:53 PM
Last Post: Ignazio Cara (Italy)
  A simple question about the HP41C or HP41CV Antoine M. Couëtte 6 936 12-16-2012, 04:06 AM
Last Post: Antoine M. Couëtte
  Problem with HP41CV Bruce Larrabee 19 1,975 09-18-2012, 09:29 AM
Last Post: Luiz C. Vieira (Brazil)

Forum Jump: