Voyageur Rubber Feet


I have acquired an 11C with cosmetic and functional issues.

As for the latter, the unit was clearly opened at one point and in the process the required pressure between a little block on the back of the circuit board and the case back is less than adequate, and the keyboard has done wonky things. A little loop of scotch tape stuck in the case back applies the need extra pressure and the thing works like a charm now.

Right now, I am interested in where one gets or how one makes rubber feet for the old Voyageurs. In the 11C, the feet are more than just cosmetics--they protect the back plate from wear and scratches when the unit is on a surface.

Grateful for any direction at all.



Hi, Les --

An eBay seller has sold sets of four feet under the name "PimpMyHP", for US$8 and free shipping. I bought a set, but haven't yet installed them. They look fine, and are quite suitable.

-- KS


Thanks, Karl, I just wrote the chap. Hopefully he will notify me if he has any more sets for sale. This calculator is clearly intended for use rather than as a collector's item (it is well scratched and worn), but still there is something incomplete about a footless Voyageur.

By the way, this model was made in Brazil and has a 29xxxxxxxx serial number. I have never heard of these things being assembled in Brazil, just Singapore and the US.



By the way, this model was made in Brazil and has a 29xxxxxxxx serial number. I have never heard of these things being assembled in Brazil, just Singapore and the US.

I've got a 1990 Brazilian-made HP-12C, so there obviously was a Voyager production line there at one time.

-- KS


I make my own from pre-stuck sheet neoprene. I use 1/32" thick material for a calculator that will be slipped into a standard HP case. For bent backplates or those just deskbound, never in a case units, I use 1/16" thick material.

While mine are not as perfect as the Pimp's (he rounds his corners like the originals), the price can't be beat (free). If you want, I can send a set your way (your choice on the thickness).

FYI: The Brazilian units used 1mm thick rubber which is thicker than the US 1/32" material, many times they peeled off and were lost from extra friction with the slip case.


Thanks Randy, I accept your offer. The back plate is peeling a bit so I should go with the thicker stuff. You have my address on record.

I am surprised I got no comments about my scotch tape pressure point fix. It seems to do the trick, but I worry about the long-term effects. But I was glad to get the thing working like normal--I was going nuts when I first got it!

Also, since I have agreed that this is to be a working calc and not a collector, I have decided to experiment a little. The scratching on the the aluminum trim was quite unsightly (I have a 15C that is near perfect, so I really notice), so I took a bit of 600 grit sandpaper and gave the surface a careful polish. I haven't been able to replicate the original brushed look of the aluminum, but the surface looks a lot less ugly, with the worse scratches reduced and the lighter ones buffed out. I wisely avoided the the display window and the plastic trim around the aluminum. Any thoughts on the appropriate and safest way to polish and clean scratched aluminum trim on the original Voyageurs?



3M makes a product out of some kind of plastic called "Scotch Brite" that works wonders giving aluminum that soft, brushed look. You probably have some in the kitchen for scrubbing pans. I've seen it attached to sponges and all by itself in 3" X 5" sheets. Also available at hardware stores. Give it a shot.


Les, you have snail mail...


Randy, the came today. Thank you so much!

I used the thicker ones.

I have to tell you that I didn't think restoring the rubber feet would make such a difference to this 11C, which I have said before works just fine but is scarred up a bit cosmetically, but it sure does. The unit feels "complete", and I am comfortable setting it on my desk to work with it that way without fearing scarring the backplate any further. And the calc sits perfectly flat too--I recall someone complaining that the Kinpo 12C and 12CP occasionally seem to wobble, with this old 11C with its new feet feels solid and steady.

Since my 15C is in almost impeccable shape this 11C is my day-to-day Voyageur. These little bits of neoprene really add much to the aesthetic and ergonomic pleasure I get from the calculator.

Many thanks again!


Possibly Related Threads...
Thread Author Replies Views Last Post
  15C LE keyboard fixed, plus: about the feet Dale Reed 2 924 01-15-2012, 04:24 AM
Last Post: Reth
  Classic Calculator Feet/Latch aj04062 0 581 03-06-2010, 05:57 PM
Last Post: aj04062
  Woodstock feet replacements? Michael Meyer 6 1,348 10-09-2009, 05:15 AM
Last Post: Vieira, Luiz C. (Brazil)
  rubber bands hp 41 ulisse-quadri 1 679 07-12-2009, 02:14 PM
Last Post: Ignazio Cara (Italy)
  Removing rubber feet from HP27S Strath Clarke (Sydney, Australia) 4 1,120 02-10-2009, 06:13 AM
Last Post: Strath Clarke (Sydney, Australia)
  HP-41CX Zengrange: remove rubber fragments Rainer Wiedemann (Germany) 0 618 01-29-2009, 07:32 PM
Last Post: Rainer Wiedemann (Germany)
  Crimson Research Voyageur Simulators for iPhone Les Wright 7 1,711 12-14-2008, 07:25 PM
Last Post: PatrickS
  Voyageur Emulators for iPhone now available through AppStore Les Wright 4 1,158 10-07-2008, 03:16 AM
Last Post: Borja
  Woodstock feet-- any good replacement? Michael Meyer 3 956 09-11-2008, 11:49 PM
Last Post: Les Wright
  Upper rubber feet on the HP 35s Ivan Latorre 7 1,617 08-10-2008, 08:56 PM
Last Post: Jeff Kearns

Forum Jump: