Spice Battery Chapter 2



#6

Yesterday I wrote that I was looking to replace the batteries in my newly acuired 37E. Thanks for those who responded.

At Radio Shack I purchased a cordless phone battery (23-967) with 2.4V and 1500mAh. They were the perfect size and had a soldered strap conecting the batteries in series. I let it charge overnight and tried it this morning. It worked for a few minutes but the the low voltage (litle red) light lit and soon thereafter the display went dead. The calculator works fine on the power cord.

Where did I make my mistake and what should I do now?

Thanks for your comments,

Dan


#7

Is the charger powerful enough to charge 1500mAh in the same timeframe as it would 600 or 650?

Edited: 16 Nov 2006, 8:55 p.m.

#8

Most likely the battery is not making good contact. You probably need to shim the strap end. I have used sticky felt like used on the bottom of pottery or Dr Scholles foot stuff..


#9

I also forgot to mention that it is normal for a fully charged modern battery to show the "low battery" signal for a while. It is actually a "high" battery.

#10

Dr Scholles foot stuff...excellent tip, thanks!!

Funny, I use them as silent blocks for my Topcat printers :-)

Etienne

#11

There is also a possibility that the calc/adapter actually didn't charge anything and that your calc "lived" on the original factory-charge of the pack.

This could be because the inner metal track of the calc is degraded or somehow doesn't make contact with the charger.

In this case, and after excluding all other possibilities, get prepared to crack open the calc(I do mean the "crack" ...horror stories ahead :-).

Etienne

Edited: 17 Nov 2006, 3:33 p.m.


#12

Thanks for all of your thoughts. The calculator works fine with the charger plugged in. I believe that the power is getting from the wall to the calculator.

The problem is that once the ac adaptor is removed then the calculator shows it low battery light after a minute. After about three minutes the display dies.

The contacts between the battery and the calculator seem solid.

Any other ideas? Does the rating of the battery have any effect?

Dan


#13

The batteries in one of my 33C's get no charge when the plug is fully inserted in the charging slot. In this case, I stop inserting the charger's plug into the calculator just before I hear the clicking sound. This is easy to diagnose if you have a meter: measuring the voltage on the battery contacts, you should obtain 2.40 to 2.55 V, depending on the charge level. On measuring again while connecting the charger, the voltage will rise to 2.61V. If it drops to 2.50-2.55V when the plug is fully inserted, then it behaves like mine. In this case, just pull the plug a bit and check if the batteries are being charged (2.6V or more on the battery contacts).

Gerson.


Edited: 17 Nov 2006, 8:03 p.m.


Possibly Related Threads...
Thread Author Replies Views Last Post
  CLASSIC/SPICE KEY LEGENDS Mike T. 2 977 08-21-2013, 04:53 PM
Last Post: Mike T.
  HP Spice Legacy in the former CCCP (MK-61) Mike Morrow 17 3,185 04-07-2013, 08:25 PM
Last Post: db (martinez, ca.)
  Working around broken Spice battery connections Les Wright 7 1,782 06-06-2012, 06:50 PM
Last Post: Mike T.
  Woodstock/Spice Keyboard Cleaning Revisited Matt Agajanian 0 664 05-12-2012, 03:43 PM
Last Post: Matt Agajanian
  Keyboard Cleanup for a Spice (or any other HP) Matt Agajanian 7 1,508 05-03-2012, 07:50 AM
Last Post: Matt Agajanian
  aOT--Battery/battery contact care advice needed Matt Agajanian 0 740 04-24-2012, 07:35 PM
Last Post: Matt Agajanian
  Spice repair - dilemma & opinions, please McAllan 1 740 02-09-2012, 03:41 PM
Last Post: McAllan
  Trying to understand Spice ROM/RAM Layout Michael de Estrada 4 1,084 06-17-2011, 08:43 PM
Last Post: Michael de Estrada
  Repairing a cracked Spice case Jeff Kearns 3 1,060 04-20-2011, 07:27 PM
Last Post: Jose Poyan
  Can I assume a Spice Calc with S/N 22xxxx is soldered? Ernst Fueloep 1 657 01-10-2011, 08:55 AM
Last Post: Randy

Forum Jump: