Powering Classics from Alkalines



#7

Will it damage a classic (HP45) to power it from alkaline batteries? I have fashioned a battery holder for a 45 I received by skeletonizing a standard 3 cell (AA) battery holder. It powers up and works fine, but I am concerned that the higher voltage might damage the calc. I am considering buying some AA nicads or NiMh batteries and a charger. I already have a 25 that has been modified to run on AA alkalines and has done so for years. I also have a 34c without a pack. It works with alkalines also, but will they damage it?


#8

Recieved wisdom says dont do this on Classics or Woodstocks, anything else is fair game. Classic electronics are fragile enough without any help. Remember that modern hi capacity ni-cads will run machines for almost double the length of time than the original pack did.


#9

Good NiCds to use are Sanyo 1100AAU. They are the same size as AA cells, and are 1100mAh. At the time many of the classics came out, the best AA sized NiCds could do about 475mAh (if that). So we're talking 2.3 times the capacity.

Stefan

#10

Hello, by accident I discovered that there is a classic NiCd-Batterypack available from HP today. The HP-Part# is 1420-0272 it works fine for my classic calculators.

Andreas Stockburger


#11

Andreas, Where did you locate the battery pack? I went to the HP Web site, then searched for this part number and I could not find it. Did you order over the phone directly from HP. Please give more information. Thanks. Jerry


#12

I used the HP parts phone number found in this forum, and the part number that Andreas provided, and ordered 3 of these, along with a battery door for my HP-28S (which masquarades as an HP-19B part, also found in this forum). I received them today, and they are the batteries, connected physically and electrically together properly, but without the plastic case around the pac. This leaves them loose in the calculator, and provides a possibility of reversing them and providing negative polarity to the calculator. I cut out some cardboard and taped it to the ends of this battery pack to keep it snug. It works well in my HP-67 and HP-75D. They cost $21.00 plus tax.


Possibly Related Threads...
Thread Author Replies Views Last Post
  Powering the HP82143A printer Steve Hunt 10 1,994 07-06-2012, 08:26 AM
Last Post: Steve Hunt
  Powering the HP41 externally Les Wright 2 787 06-17-2012, 11:48 PM
Last Post: Diego Diaz.
  USB Chargers for Classics Matt Agajanian 3 972 05-07-2012, 08:10 PM
Last Post: Matt Agajanian
  Just some Classics eye candy Geoff Quickfall 4 956 06-17-2011, 12:46 AM
Last Post: Hal Bitton in Boise
  Wire Gauge in Classics aj04062 2 737 10-30-2010, 07:40 PM
Last Post: aj04062
  Charging 'classics' from a USB port Katie Wasserman 16 2,556 10-06-2010, 02:54 PM
Last Post: Juergen Keller
  Simulate "load" (or whatever) of batteries in classics hooked to chargers? Paul Brogger 14 1,828 01-09-2010, 12:16 PM
Last Post: Eric Smith
  Restoring Classics: 409 removed some lettering! Mark Henderson 12 2,028 12-12-2009, 07:35 PM
Last Post: Marcus von Cube, Germany
  Silver line above on-off swiths Classics Ronald 1 580 10-19-2009, 12:45 AM
Last Post: geoff quickfall
  Anode and cathode driver chips interchangeable on Classics? Dan W 0 484 08-08-2009, 01:45 PM
Last Post: Dan W

Forum Jump: