Posts: 40
Threads: 7
Joined: Jan 1970
With my "Emu41" (thanks Jean-Francois !!!!) I can't work with these settings:
[MODULES]
; page size filename
0 12 Rom41-CX.bin
3 4 XFuns-CX.bin
5 8 Time-CX.bin
6 4 Prter1E.bin
7 4 ILmod-1H.bin
8 8 Ccd-b.bin
A 12 Adv1B.bin
All it's OK if I set only CCD or only Advantage at page 8.
Are CCD and Advantage modules compatible?
Thanks for any info.
(remove all "_NOSPAM_" from my e-mail address)
1234
Posts: 40
Threads: 7
Joined: Jan 1970
Sorry for bad layout.
The settings are:
[MODULES]
0 12 Rom41-CX.bin
3 4 XFuns-CX.bin
5 8 Time-CX.bin
6 4 Prter1E.bin
7 4 ILmod-1H.bin
8 8 Ccd-b.bin
C 12 Adv1B.bin
Thanks again
Posts: 1,841
Threads: 54
Joined: Jul 2005
Hi,
my suggestion is to use the CCD OS/X file
from TOS instead of the normal CCD-B.
This way you'll have all the CCD OS extensions nad more,
but without duplicated matrix stuff.
Apart from that, the CCDD (or CCD OS/X)
only uses one 4K block, not two.
Just take a look at TOS (The Other Site)
Raymond
Posts: 412
Threads: 40
Joined: Mar 2006
Hi Claudio,
What problem did you get? CCD and Advantage use same ressources (buffer number, X-M files, ...), so it is not recommended to mix matrix functions of both modules. Apart of that, it should possible to install both of them in the same machine.
But I agree with Raymond, the best configuration is CCD OS/X + Advantage.
J-F
Posts: 40
Threads: 7
Joined: Jan 1970
Quote:
What problem did you get?
With this .ini:
8 8 Ccd-b.bin
A 12 Adv1B.bin
the output of CAT 2 is:
-EXT FCN 2D
-CX EXT FCN
-TIME 2C
-CX TIME
-PRINTER-
-MASS ST 1H
--
-CTL FNS
-W&W CCD B
-ARR FNS
-HEX FNS
-I/O FNS
-ADV FNS
-XF/M FNS
If I switch the 2 modules with this .ini:
8 12 Adv1B.bin
A 8 Ccd-b.bin
the output of CAT 2 is:
-TIME 2C
-CX TIME
-PRINTER-
-MASS ST 1H
-CTL FNS
-ADV CONV B
-ADV MTRX
-ADV MATH
-ADV TVM
-EXT FCN 2D
-CX EXT FCN
You can see that I can have or CCD or Adv, but not all two together.
CCD OS/X is a great module, but I can't understand why the
old CCD-B can't work with Advantage. They have different page,
different XROM numbers, so ........ why..????
1234
Posts: 1,253
Threads: 117
Joined: Nov 2005
Claudio,
Have you tried using "10" instead of "A" to denote the second module location?
Regs,
ÁM
Posts: 412
Threads: 40
Joined: Mar 2006
You're right, Angel, of course. I didn't notice it ...
J-F
Posts: 40
Threads: 7
Joined: Jan 1970
Wow...was too much obvious!!!
(shame on me) :-((
Anyway I thank all for your help.
1234