32s keyboard flex problem
#1

I tend to inherit broken things other people think I can fix, as is the case with my 'new' 32s:
The middle keys esp. the "[sst] 4 5 6 [multiply]" row don't register unless the upper chassis is pushed down. The whole chassis has a permanent bow to it, bowed up across the short section, bowed down across it's length. I read the archived posts by Mr's Brogger & Duell regarding opening up pioneers, and the opening was a success. 'Unflexing' the upper plastic seems a bit difficult without cutting all the plastic welds, which would really screw things up. Anyone have a method of fixing this problem? I seem to remember reading about Pioneer series keyboard flex before but couldn't find the post.

AtDhVaAnNkCsE
Ned

#2

The bow in the plate is common in older Pioneers and is not the problem. The problem is the small foam pad under the keyboard connector - it is either out of position or it has lost is spring force, perhaps a combination of both. Shimming the pad with several layers of flexible tape is usually all that is required.

#3

Hi Randy,

In order to shim, do you need to take the chassis all the way apart?

Does this rule--shimming to bring a keyboard back to life-- also apply to the 48 series?

Best regards,

Bill

#4

I'm not sure what you mean by "taking the chassis all the way apart". You only have to remove the logic board from the frame. Anything beyond that and it's tough to get it back together.

The 48's have identical issues/fixes.

#5

Yes, turning the metal keeper tabs back parallel with the slots should free the circuit board. See:
http://www.hpmuseum.org/guest/brogpion.htm
thanks for the tip about the pad. I'll take the leap tonite and undo the tabs.

-Ned

#6

okay upon removing the rear chassis and the pcb, I saw that the problem (with most pioneers maybe) is that 2 hooks, or teeth on the front chassis became detached from the metal plate. In this case, the front chassis was allowed to flex out, causing lack of contact at the keyboard connector. This is just below the lcd, where the keyboard connects to the pcb via the printed mylar. Shimming the foam pad might work also, but hooking the teeth back to the metal solves the problem. Poor design IMHO. The front chassis provides no stiffness, the metal plate should have been channelled for stiffness.

-Ned



Possibly Related Threads...
Thread Author Replies Views Last Post
  HP 32s LCD part Trisnadi Sutrisno 2 717 08-27-2013, 02:12 PM
Last Post: Han
  HP-32S II Expansion Matt Agajanian 14 2,063 07-21-2013, 10:19 PM
Last Post: Matt Agajanian
  HP 32S-II Vertical Curve Program Ron Cardwell 2 763 05-20-2013, 07:54 AM
Last Post: Thomas Klemm
  Updated HP-41 Flex-PCB replacement guide. Diego Diaz 2 755 03-12-2013, 12:36 PM
Last Post: Diego Diaz
  32Sii keyboard problem Peter Klein 4 928 07-25-2012, 01:53 AM
Last Post: Peter Klein
  HP-29c keyboard dead 2nd row problem Xavier A. (Brazil) 6 1,225 07-17-2012, 07:09 AM
Last Post: Xavier A. (Brazil)
  HP-41's ARCL on the 32S-II Matt Agajanian 2 644 05-04-2012, 04:45 PM
Last Post: Matt Agajanian
  Tips & Programs for the 32S Matt Agajanian 0 447 03-16-2012, 02:24 AM
Last Post: Matt Agajanian
  Just how tough is a 32S-II ? Matt Agajanian 12 1,757 03-11-2012, 05:36 AM
Last Post: Thomas Radtke
  HP 35S keyboard problem Nick R 26 3,002 08-11-2011, 12:00 PM
Last Post: Thomas Radtke

Forum Jump: