HP-42S with Electroluminescent screen and simple I/O port
#1

Hi,

I had a couple of ideas some years ago about installing an electroluminescent display on an HP42s. I finally didn't do it but I wanted to share some photos here.
It took too long so I put it in the form of an article. Please visit it if you feel interested:

http://www.hpmuseum.org/cgi-sys/cgiwrap/hpmuseum/articles.cgi?read=1240

If anyone in the forum wants to do it, I can help with anything except the electronics and programming areas.

jose

Edited: 26 Mar 2013, 5:05 p.m.

#2

Nice work!

I actually owned one of those Hook-uP units, purchased from Educalc (RIP), but I no longer have it.

#3

Hi,

Impressed by the mech-mods, and milling!

A high level hobbist job indeed, certainly not for the average 42s user/owner, but admirable from a HW guy point of view.

Good to see these sort of things still happen... ;-)

Cheers.

Diego.

#4

Thanks. Do you know if there exist something similar to connect the hp42s to a modern pc (donwload)?

#5

Hi,

great work!


For the 42S I/O : Yes, via an indirect proof. Christoph Giesselink demonstrated on the famous Allschwil meetings how to output and input data over a serial connection between the HP-28S and a normal PC terminal program, Hyperterminal in this case.

This should also work with an HP-42S .

Ray

#6

Hi Jose,

I don't know of any (successful) project allowing a PC<>42s interconnection.

A few years ago, I built a very rudimentary MLDL-like interface by connecting the spare ROM pads to a PIC18F452 microcontroller via a couple of Flex PCB's salveged from LCD display units.

Eventually, this should have allowed full control/access to the RAM as well as an extra space for saturn code expansion.

The HW part was (more or lees) easy; but the required SW interfaces went far beyond my limited programming skills. Also the fact that an HP-42s must be "destroyed" to built such device, represents a serious drawback in order to find beta testers; not to say "user's target market" for the project... :-)

It was very funny nonetheless.

Best wishes.

Diego.

Edited: 26 Mar 2013, 9:45 p.m.

#7

I see. The same happened to me in choosing the calculator. I would never have thought in using a flawless unit for the project. In my case I used an HP-42S that needed repair for the keyboard and had some scratches on the bezel. So it needed to be opened.

#8

Some years ago I worked on an RS232C interface for the Lewis chip based calculators like the HP28S and HP42S. This project never leaved the proof of concept state on a HP28S.

It's quite unknown that the Lewis chip output port for the IR-LED is bidirectional. So I made a primitive hardware interface to connect the IR-LED port of a HP28S to the RXD and TXD pins of the RS232C interface. The power supply of this interface is generated over the RTS/TXD pins and in idle state < 4 uA from the calculator battery.

The RS232C protocol 2400 baud, no parity, 8 bit, 2 stop bits (2400,N,8,2) was implemented in software. Because of polling the input pin, standard baudrates over 2400 aren't possible with a Lewis chip at a nominal strobe clock frequency of 1MHz.

I mentioned this project here: http://www.hpmuseum.org/cgi-sys/cgiwrap/hpmuseum/archv016.cgi?read=101692

Quote:
7) HP28S serial

What's new on the HP28S serial project. I recognized many problems on running when I tried to port this method for ROM uploading over the Ir port. The main problem was the time delay for creating the RS232C signal. In the version I demonstrated two years ago I hadn't thought about different timing on Saturn commands executed on an even or add address. Because the program is lying in calculator RAM the transmitter routine can begin on an even or odd address depending on the program version and the base address of the complete program. I fixed this in spring this year by executing the time critical part in display RAM which is directly accessed by the internal Saturn bus having equal timing on even and odd address.

Next step is a protocol (XMODEM) layer.


#9

That looks like a lot of work, with efforts coming from everywhere.



Possibly Related Threads…
Thread Author Replies Views Last Post
  HP-41 module covers and side port cover Nate Martin 1 1,489 12-02-2013, 01:51 AM
Last Post: Giancarlo
  Simple Tetris. free for you to improve on cyrille de BrĂ©bisson 3 1,898 11-20-2013, 05:43 PM
Last Post: Erwin Ried
  Prime screen scratches - Use a screen protector Eelco Rouw 11 3,233 11-19-2013, 10:16 PM
Last Post: Eddie W. Shore
  [HP-Prime] Simple Game (Bugs) CompSystems 1 1,398 11-01-2013, 10:18 AM
Last Post: Han
  Stylus for Prime screen steindid 6 2,287 10-22-2013, 02:06 AM
Last Post: Alberto Candel
  Sending from graph to home or CAS screen Richard Berler 6 2,228 10-06-2013, 03:29 PM
Last Post: Tim Wessman
  HP48GX screen replacement Francisco Quiles 9 3,779 10-03-2013, 09:17 PM
Last Post: Francisco Quiles
  Yet another benchmark port on the wiki: Savage Pier Aiello 35 9,363 09-26-2013, 03:22 AM
Last Post: Pier Aiello
  hp50g screen weird line Sok-khieng Chum Hun 2 1,569 09-10-2013, 08:11 AM
Last Post: Sok-khieng Chum Hun
  Simple Math Question Namir 2 1,383 08-09-2013, 06:13 PM
Last Post: Eddie W. Shore

Forum Jump: