hp 41 series wire-wrapped connector question.
#1

This is probably an easy question for some, but as I assemble my 41CL, I am curious how the wire-wrapped connector (between the Nut/Newt PCB and the keyboard/display PCB) maintain pin/pad separation? It looks like two coils of wire (see link to Geoff's pic). Is there a varnish-insulated loop every few coils to maintain pad separation? I said it was an easy question for some- just not me :-)

Thanks,
Matt

p.s. It looks like the serial number sticker on the back of my NEWT board is "41". Thanks Monte (Don't tell me they all say "41" ;-)

Edited: 19 June 2012, 12:13 a.m. after one or more responses were posted

#2

Hi.

In fact, it looks more like small pieces of flex circuit with single, parallel thin copper tracks (golden plated). Then the flex circuits wrap the two small rubber, silicon tubes. They are actually spare little tracks, not one single coil. I have once disassembled one of this and could never reassemble it because it broke in many parts. 8^(

As they are very thin tracks they do not shorten one pad with another in the main PCB because more than one of them fits in the space between pads. Note that there are two other separated assemblies like these - somehow lengthier - in the earlier HP41 LCD's (see this picture)

Hope this helps clarifying.

Cheers.

Luiz (Brazil)

Edited: 19 June 2012, 12:15 a.m.

#3

Thanks for the good explanation Luiz. I understand that it couldn't possibly be a a single coil, but that it looked like it was.
Sorry you had to take-one-for-the-team to learn how it all worked, but we're all the better because of it. Thanks Luis.
Matt

#4

Hi, Matt.

Please, have a look at this thread (chances are you have already seen it). For me, this is one of the best solutions for an HP41 mock up, either testing or developing purposes. But I also considered it a final solution when you have a good keyboard and wish to have a fail-proof, working calculator.

I found someone in Brazil that could provide me with a minimum quantity of 250 units, but it would cost me too much. I thought about trying to find people that might be interested on sharing the $$$ burden, but then again I missed the folks.

And you are correct: the little thing looks like a continuous wire assembly, as in a coil.

Cheers.

Luiz (Brazil)



Possibly Related Threads…
Thread Author Replies Views Last Post
  HP-41(CL): The easiest way to transfer FOCAL programs from a Linux PC to the HP-41 Geir Isene 13 5,782 12-05-2013, 02:40 AM
Last Post: Hans Brueggemann
  Non-Prime question alert: Hp-41 and synthetic instructions Marcel Samek 11 4,136 11-04-2013, 09:31 PM
Last Post: sjthomas
  HP-10C Series Family Photo Max Stone 5 2,235 10-24-2013, 10:31 PM
Last Post: Eddie W. Shore
  [HP-Prime] connector made with printer3D CompSystems 0 1,026 10-18-2013, 04:53 PM
Last Post: CompSystems
  HP 50g Takes hours to compute a convergent series Matthew Richards 10 3,198 05-14-2013, 03:30 PM
Last Post: Thomas Klemm
  HP Calc Series Mic 3 1,621 03-21-2013, 01:34 AM
Last Post: Mic
  HP 48G series -> 20 years NACHO 0 963 12-13-2012, 09:40 AM
Last Post: Nacho
  Swiss clones of the HP Voyager series WaltMaken 10 2,921 11-30-2012, 11:40 AM
Last Post: Harald
  HP-48: extract coefficient of power series Thomas Klemm 3 1,573 10-21-2012, 11:42 PM
Last Post: Han
  Best Keyboard of the HP 28/48/49/50 Series Eddie W. Shore 9 3,331 07-12-2012, 07:21 AM
Last Post: Dave Britten

Forum Jump: