Another stupid WP34S question
#1

What a unit!

So the IR is all set physically in the calc. The Quartz crystal and one cap has been added. Awaiting the trimming cap from Mouser.

So I have been busily programming (without the overlay which I am awaiting from Eric). Actually getting to know the key locations without the overlay.

So of course, I have made backups in the flash and I see that I can save these when I SAMBA flash my calc to the IR and quartz bin.

At the moment I have full bin. I noticed in the manual that I can flash using 'ON + 6' instead of the ERASE button on the cable.

Would someone please confirm that I substitute the 'ON + 6' then release then continue by (FROM THE MANUAL):

3. Turn the calculator on by pressing and releasing the ON/CE
bottom left).
4. Press and hold the 'ON + 6' keys
5. Press and release the RESET button on the cable.
6. Press and release ON/CE to turn the calculator on again.
8. Press and release RESET again.
9. Press and release ON/CE on the calculator. It will look dead.
Don’t care – see the note above.
10. Click "Send File" in MySamBa and wait for it to finish
transmission (it will only take a few seconds). If you have the
FTDI USB/serial adapter, you will see the blue TX light
blinking.
11. Press and release RESET once more.
12. Press and release ON/CE. Your calculator should turn on as a
WP 34S now.

You will notice the ERASE button has been substituted by the 'ON + 6' sequence.

Cheers, Geoff

no biggy but I would rather not input my programs again!

#2

ON-6 does work but you need to put the calculator into debug mode first with ON-D. I did not use the serial cable last two times I flashed mine as I have installed one of Harald's fine USB and printing boards. To flash I did the following:

ON-D
ON-6 (I think you may need to press 6 a second time to confirm but
the display will go blank)
ON
Then from mysamba I uploaded the flash file.
#3

Thanks Paul!



Possibly Related Threads…
Thread Author Replies Views Last Post
  Stupid idea of the day: 41-compatible watch bhtooefr 0 977 03-31-2013, 08:23 AM
Last Post: bhtooefr
  Simple? programming question [WP34S] Shawn Gibson 3 1,411 03-15-2013, 11:56 AM
Last Post: Didier Lachieze
  [wp34s] xtal question jerome ibanes 9 2,856 02-05-2013, 05:35 PM
Last Post: Massimo Gnerucci (Italy)
  [WP34S] WP34S firmware on the AT91SAM7L-STK dev kit? jerome ibanes 1 1,173 10-04-2012, 04:59 PM
Last Post: Paul Dale
  more question regarding complex operations using complex number on wp34s wildpig 22 5,195 09-02-2012, 12:54 PM
Last Post: Walter B
  WP34S solver question Reth 22 5,848 07-13-2012, 06:55 PM
Last Post: Paul Dale
  WP34s Flash Question rgray 18 5,464 06-19-2012, 03:20 AM
Last Post: Cristian Arezzini
  Stupid question number...WS34P Geoff Quickfall 16 4,110 06-16-2012, 07:04 AM
Last Post: Paul Dale
  WP34S beginner question Geoff Quickfall 8 2,393 06-08-2012, 09:55 PM
Last Post: geoff quickfall
  [WP34s] Assembler question fhub 6 2,108 05-14-2012, 03:08 PM
Last Post: Marcus von Cube, Germany

Forum Jump: