Help with 41CV - memory problem ?
#1

Hi,
I am repairing a 41CV (fullnut, s/n 2202S40037) for a workmate and would appreciate some help. I refurbished the card reader, fixed the battery contacts and repaired the screw posts - cosmetically it is excellent. I put it back together and it appears to work ok performing simple calculations. STO and RCL work and the values are preserved when powered off.

I then entered a 4 line program and when executed the 41CV locks up and has to be powered off to regain control. Executing GTO .. results in a lockup with 'PACKING' showing on the display. I can read pre-programmed cards but they also lock up the 41CV. I am guessing this is indicating a problem with the memory IC's.

The IC's are as follows :

ILB738, ILB739, ILB740 - ROMS ?

ILA701

ILE701, ILE702, ILE703, ILE704, ILE705 - memory ?

I have removed the abovementioned chips but do not have another 41CV to test them in.

Any advice on how to proceed will be appreciated as I would like to surprise my friend by returning his 41CV to full health.

Regards, tim.

#2

Hi Tim,

On 1st look it sounds like there are no program Registers assigned.
Just XEQ SIZE , and fill the prompt with a Value, like 050 .
The above number tells the HP-41 to assign 50 of the available registers as Data Storage Registers, and to use the remaining memory as program storage.
Please also consult the Manual for more details.

HTH

Ray

#3

The CV from a memory lost state should assign program registers automatically.

XEQ SIZE 000
switch to prgm mode

and record the number of program registers available and let us know if you see 319.

that would indicate that all RAMs are functional.

Let us know what you see.

Geoff

#4

Hi,
thanks for the tips Raymond and Geoff.

As I have already desoldered and removed ILA701, ILE701, ILE702, ILE703, ILE704, ILE705 I am wondering whether I can solder them back in a specific sequence to help diagose the problem ?

For example if ILE701 is the first set of memory registers (64 ?) and there are no other memory chips present, would XEQ SIZE 000 show 64 if ILE701 is ok ? With a faulty memory chip in-circuit would the XEQ SIZE 000 command then fail, indicating that the last chip fitted is faulty ?

Here I am assuming the ILA701 is memory registers 1-64, ILA702 is registers 65-128, etc, however this is just a guess.

Or should I put them all back in-circuit and proceed with fault finding ?

Thanks, Tim.

#5

1LA701 is the "status registers". The calculator needs that and 1LE701 at a minimum (along with all the ROMs) to work at all.

#6

Hi Eric,
when I said "....Here I am assuming the ILA701 is memory registers 1-64, ILA702 is registers 65-128, etc, however this is just a guess...." I should have said ILE701, ILE702, etc.

Anyway, I soldered the ILA701 and ILE701 back in (ILE702 to ILE705 are not in-circuit) and when I switch to program mode the display shows '000 REG 46'. GTO .. initiates 'PACKING' and a lockup. Does this mean the 41CV is only seeing the first 46 registers of the ILE701 and that it is a faulty chip ? If so, any tips on finding an ILE701 as I am not keen on buying another 41CV just for 1 chip.

I think the display also showed '000 REG 46' before I removed ILE701 to ILE705.

Thanks for you help. Timw.

#7

You are correct that 1LE701 contains the first 64 "user" memory registers. The "000 REG 46" is the correct display after entry to PRGM mode from MEMORY LOST, because the partition between registers registers and program space is fixed somewhere in the middle of the 1LE701 chip.

With all RAM chips installed, you should be able to access (STO and RCL) registers 00 though 272, but you have to use indirect addressing to get at registers above 99. For instance, you could do something like:

272 STO 00
1.23456789E41 STO IND 00
CLx
RCL IND 00

and you should bet the stored number back. (Press the gold shift key for IND.)

The other ways to look at the memory size are:

XEQ alpha SIZE alpha 000 -- configures for NO user data registers
PRGM - tells you how many program registers are available, e.g.,
00 REG 63, 00 REG 127, 00 REG 191, 00 REG 255, or 00 REG 319

Or, with the Extended Function/Memory module:

XEQ alpha SIZE? alpha

Failing during PACKING suggests that there is another failure. Most likely this would be either a ROM, the 1LA701 RAM, or the processor chip (1LA5-0001, 1LE3-0002, or 1LF5-0002). It is obvious that the ROMs, 1LA701, and processor are at least partially working, which makes this difficult to pin down.

The official service procedures would tell you to replace a series of chips until the calculator works correctly. This is obviously not practical for you, since there is no source of replacement parts aside from other calculators. At this point it sounds to me like your 41CV is only useful as a possible parts donor.

#8

Quote:
At this point it sounds to me like your 41CV is only useful as a possible parts donor.

...or as a home for a CL board. :-)

Edited: 8 Sept 2011, 2:15 a.m.



Possibly Related Threads…
Thread Author Replies Views Last Post
  HP Prime: problem with the memory of calculator during the debug process? Carlos CM (Mexico) 7 3,597 12-06-2013, 12:34 PM
Last Post: Carlos CM (Mexico)
  HP-41CV - A Walk Down Memory Lane Tom Lewis 9 2,851 03-18-2013, 11:14 PM
Last Post: BShoring
  HP-41CV power problem Don Davis 2 1,331 10-11-2012, 09:13 PM
Last Post: Don Davis
  41 User Memory vs System Memory Gerry Schultz 6 2,512 07-01-2012, 12:02 AM
Last Post: Monte Dalrymple
  41CV Fullnut shows "Memory Lost" consantly John Robinson 7 2,307 05-27-2011, 05:51 PM
Last Post: John Robinson
  HP 41CV repair - constant Memory Lost message Nigel Bamber 2 1,143 08-21-2009, 01:44 AM
Last Post: Nigel Bamber
  Memory problem on 48G+ Iqbal 1 930 08-06-2009, 04:35 PM
Last Post: Raymond Del Tondo
  Early HP-41C PCA picture as well as memory problem... Geoff Quickfall 15 3,611 08-04-2009, 07:56 PM
Last Post: Gene Wright
  memory problem on HP48G Teun Vorselman (netherlands) 1 917 03-17-2007, 10:08 PM
Last Post: James M. Prange (Michigan)
  41CV memory Paul Beijer 6 1,963 01-16-2007, 04:26 PM
Last Post: Karl Schneider

Forum Jump: