HP-67 Error message
#1

Hi ya all,

Seeing there is some activity regarding 67's, who can tell me what is ailing this unit? Is the processor fried? I picked this up from Goverment Auction (los alomos lab source)

Note: I have the back off and am pressing down to make contact. It is behaving the same way before I took it apart.

Please see the video below.

Video

Pressing keys will halt the cylcling. It will everntually stop and seems to repeat the same code.

#2

"Could be a lot of things..." How's that for helpful? :-)

First, don't try reading any more cards until you take a look at the friction roller for the reader - it's probably turned to goo unless somebody has replaced it. (Although I'm somewhat surprised it actually pulled the card through on yours...)

The problem could be as simple as a bad battery - have you checked the voltage? Tried running it from a bench supply?

The next lucky break would be a bad/dirty connection between one of the three internal boards, a dirty power or run switch, etc. That will require disassembly. If you want to try that, check out the guides
here. Disassembly requires some experience working on electronics and small mechanical gizmos. The guides provide enough information/photos to let you decide if you're comfortable with trying it.

If you don't want to try a repair, I'm sure you can sell it easily here or on the 'bay as a parts unit.

Regards,
Bob


Edited: 15 May 2011, 8:57 a.m.

#3

This wheel actually looks very good. I am amazed.

I've tried a new battery (worked on other 67 I have). I don't have a bench supply so that experiment is out. I will check voltage and make sure it is fully charged.

I'll try some deoxit on the contacts. I cleaned the switches with iso-alch already.

does anyone know what boards are interchangeable between the 67 & 65? I have a 65 with a card reader board that has been ravaged by a leaky battery. Can these be swapped?

#4

HP-65 Internals

HP67 Internals

The only thing the two boards have in common is the same 28 pin connection area :-(

Hard to tell what is wrong but based on the most common 67/97 failures, I'd suspect a faulty rom.


Edited: 15 May 2011, 1:34 p.m.



Possibly Related Threads…
Thread Author Replies Views Last Post
  [HP Prime] "Error while checking exact value with approximate value, returning both!" Chris Pem10 13 4,945 12-06-2013, 05:12 AM
Last Post: parisse
  MS advert shows spreadsheet with obvious error BruceH 3 2,146 11-14-2013, 09:50 AM
Last Post: Bill (Smithville, NJ)
  HP Prime: Rounding error in determinant Stephan Matthys 3 1,607 10-25-2013, 09:29 PM
Last Post: Walter B
  HP Prime Error: Summation Upper Bound > 1000 HP Pioneer 2 1,351 10-25-2013, 11:32 AM
Last Post: steindid
  Prime Error or Mine? toml_12953 12 3,531 10-22-2013, 10:35 AM
Last Post: toml_12953
  Explaination on How to Reset Caculator in Users guie: error Harold A Climer 5 2,513 10-15-2013, 02:11 AM
Last Post: cyrille de Brébisson
  Formatting the app view message with bullets (dots) Geoff Quickfall 4 1,708 10-14-2013, 06:22 PM
Last Post: Geoff Quickfall
  Repair of HP-34C - Error 0 and Error 9 Jeff Kearns 3 1,644 10-11-2013, 12:29 PM
Last Post: Randy
  message for Andreas Grund Don Shepherd 0 770 09-26-2013, 03:56 AM
Last Post: Don Shepherd
  Message to Eric Rechlin Etienne Victoria 3 1,504 09-24-2013, 07:50 PM
Last Post: john mantooth

Forum Jump: