Re: Printing quality on HP-97
#1

Here is the scan , but in reality the difference is more importnat than on the scan :
The printing before i opened the HP-97 is a lot darker than after.


Hope somebody can help me.

Thanks

Christophe Dubreuil

#2

Hi Christophe,
if the paper is the same and you haven't take apart the printer or swap the printer PCB with another one, it's very strange.
If my eyes are still good, you are loosing one resistor of the thermal printer head, the third from the bottom. You should measure each resistor from the edge of the flat cable that is connected to the printer's PCB. The value of each resistor should be about 11 ohms.
If you have one spare printer PCB, try to swap it on the printer.
Let me know after you have done this series of checks.

Regards

Ignazio

#3

It is the same paper ... I havent touched the printer part of th HP-97 (or unwillingly).
I agree that one line is missing (but not entirely , there are very small dots where there shoul be normal ones) , i'll check the resistor , but as i said all the printing is lighter also.

Regards

Christophe

#4

Quote:
but as i said all the printing is lighter also.

I don't know why this changed but there's and easy and documented fix for this in the service manual.

Quote:
2-31. The remaining comparators in U4, along with the
resistor network in U5, produce the variable duty-cycle
signal STB, which is nominally 10 kHz. The STD signal
will change its duty-cycle to keep its rms value constant and
thus print intensity constant. By changing the value of R8,
the nominal duty-cycle of STD can be changed to adjust
print intensity.

There's no way to tell what the current value of R8 is without looking. Each HP-97 was shipped from the factory with a selected value, they list values from 34.8K to 196K in the service manual, but they've all 1% resistors.

-Katie

#5

I finally went thru the service manual ... i checked the various things i could (resistances and voltages) and all seems OK , i guess it may be one of the transistors that is weak (explaining meybe the light line).

I should get an oscilloscope ro further investigate.

But as i pointed out ... it happened after i opened it for fixing the magnetic card reader ... it was perfectly working before ...i should have inadvertably modified something.

I am a bit reluctant to change R8 and modify it. I guess i will use it as it is, and if it get worst i then will proceed further.

Thanks to the community.

Christophe Dubreuil

#6

Hello Christophe,
I live in Italy, and I can send you a quad transistor 1858-0044, for free.
Let me know your address if you are interested.

Regards

Ignazio



Possibly Related Threads…
Thread Author Replies Views Last Post
  Printing the HP Prime manual BobVA 3 1,735 10-25-2013, 09:53 PM
Last Post: BobVA
  3D printing custom molds Han 3 1,630 08-02-2013, 03:26 AM
Last Post: Bruce Larrabee
  Printing HP 9825 data Norman Pillsbury 3 1,510 06-01-2013, 10:08 PM
Last Post: David Ramsey
  The decline of Soviet calculator quality Michael de Estrada 5 1,842 05-31-2013, 02:48 PM
Last Post: Thomas Radtke
  DM-1x Silver vs. DM-1xCC Aluminum quality? bhtooefr 11 3,250 04-14-2013, 07:08 PM
Last Post: bhtooefr
  Does IR printing not work on your converted WP34s? Then read on... Harald 3 1,601 04-04-2013, 05:46 PM
Last Post: Harald
  WP34s IR Printing Update? Thomas Chrapkiewicz 2 1,220 02-24-2013, 01:53 PM
Last Post: Marcus von Cube, Germany
  is there a printing error in the HP 50G Quick Starrt Guide? Al 12 3,041 11-23-2012, 07:07 PM
Last Post: Al
  WP 34S Printing Harald 15 3,839 04-28-2012, 08:54 PM
Last Post: Les Wright
  WP 34S: IR printing - update Marcus von Cube, Germany 79 14,832 04-25-2012, 11:24 AM
Last Post: Walter B

Forum Jump: