42S Problem - Switches off straight away.
#1

Hi
I inherited a 42S and it switches off imediately after switching on. In some cases the display will flash for a split second, in other cases it doesn't show anything. If I press the ON key fast enough I can keep the display on until I release the key.

The self test (ON-LOG) works just fine, and passes OK. But at the end it just switches off. ON-ROOT (the reset function?) works and very briefly display "Machine Reset"

I can even adjust the contrast, and even get it to do calculations if I press a key fast enough at power on, but it switches back off again as before.

Anyone know what is wrong? Is there any higher level reset function I can try?

The batteries are brand new and tested.

Thanks
Dave :)

#2

Hi, David;

you can reset the entire USER memory contents to its default state by pressing three keys simultaneously: [ON],[Sigma+]and[XEQ]. Yeap, these are the keys at the three corners: left-down, left-up and right-up. With the calculator turned to off, press them all, then release them in the reversed order writen above: release [XEQ], then release [SIGMA+], then release [ON]. A particular message indicating memory loss must appear. This is the 'master reset', although it still depends on software to resume. Leaving the calculator without batteries for some time might cause the best reset ever, but this demands time (some days, maybe).

Hope this helps.

Success!

Luiz (Brazil)

#3

Quote:
Hi, David;

you can reset the entire USER memory contents to its default state by pressing three keys simultaneously: [ON],[Sigma+]and[XEQ]. Yeap, these are the keys at the three corners: left-down, left-up and right-up. With the calculator turned to off, press them all, then release them in the reversed order writen above: release [XEQ], then release [SIGMA+], then release [ON]. A particular message indicating memory loss must appear. This is the 'master reset', although it still depends on software to resume. Leaving the calculator without batteries for some time might cause the best reset ever, but this demands time (some days, maybe).

Hope this helps.

Success!

Luiz (Brazil)


Thanks Luiz
I tried that and I got "Memory Clear", but it still keeps turning off!

I'll leave the bateries out and see what happens.

Any other suggestions?

Thanks
Dave :)

#4

Try to install new fresh battery, maybe the battery low but not low enough announce on display,on my experience low battery always make the calculator unstable.

#5

Agreed.

My experience with the battery indicator on the 42s is that it doesn't always represent reality. I had a vexing issue with printing to the printer on my 42s, and I thought it might be the batteries, but the indicator was all "nope, you're good!", so I discounted it. After another 20 minutes, I switched them out anyhow and everything printed just fine.

So, like the previous poster mentioned, put in some new batteries.

thanks,
bruce

#6

Quote:
Agreed.

My experience with the battery indicator on the 42s is that it doesn't always represent reality. I had a vexing issue with printing to the printer on my 42s, and I thought it might be the batteries, but the indicator was all "nope, you're good!", so I discounted it. After another 20 minutes, I switched them out anyhow and everything printed just fine.

So, like the previous poster mentioned, put in some new batteries.

thanks,
bruce


No joy, fresh batteries makes no difference. All batteries measure 1.57V

Any more ideas?

Anyone know how the 42S latches the power on? Is it that small SOT23 package (MOSFET?) I see on the back of the board in the internal photos? Or is it simply low power logic within the ASIC?

It's got to be a program thing, as the power latches on fine when doing the self test.

Thanks.
Dave :)

#7

Quote:
Hi I inherited a 42S and it switches off imediately after switching on. In some cases the display will flash for a split second, in other cases it doesn't show anything. If I press the ON key fast enough I can keep the display on until I release the key.

The bequeathed HP-42S isn't running a program like the following at startup, is it? ;-)

LBL 00
SF 11
OFF
GTO 00

Flag 11 will run the "pointed-to" program at startup, upon which the flag is cleared -- a feature carried over from the HP-41.

Seriously, running the self-test will allow the user to easily escape this "trap" of a program.

-- KS

#8

Quote:
The bequeathed HP-42S isn't running a program like the following at startup, is it? ;-)

LBL 00
SF 11
OFF
GTO 00

Flag 11 will run the "pointed-to" program at startup, upon which the flag is cleared -- a feature carried over from the HP-41.

Seriously, running the self-test will allow the user to easily escape this "trap" of a program.
-- KS


I have no idea, as it can't switch on (other than self test mode) I cannot check.
Surely if there was such a program in there then it would be cleared when the batteries are removed?

Dave :)

#9

Hi, David;

any user-related data (programs, key assignments, matrices, register data, ALPHA contents, etc.) is erased after a master clear procedure, cofirmed with the 'Memory Clear' message you saw earlier. The small program Karl mentions may actually cause the auto-off behavior you described, because it sets auto-run flag (11) and turns the calculator off. In this case, subsequent attempts to turn the calculator on will cause it to turn itself off straight.

I have seen some HP42S with weird behavior, and in some cases I could interfere, resoldering the RAM chip and the other SMD components (two, I guess) solved the problem. Any chance that you'd open yours and try this? If you are not skilled in electronics maintenance, please, do not try it.

My 2¢.

Luiz (Brazil)

Edited: 22 Nov 2006, 11:01 a.m.

#10

Quote:
Hi, David;

any user-related data (programs, key assignments, matrices, register data, ALPHA contents, etc.) is erased after a master clear procedure, cofirmed with the 'Memory Clear' message you saw earlier. The small program Karl mentions may actually cause the auto-off behavior you described, because it sets auto-run flag (11) and turns the calculator off. In this case, subsequent attempts to turn the calculator on will cause it to turn itself off straight.

I have seen some HP42S with weird behavior, and in some cases I could interfere, resoldering the RAM chip and the other SMD components (two, I guess) solved the problem. Any chance that you'd open yours and try this? If you are not skilled in electronics maintenance, please, do not try it.

My 2¢.

Luiz (Brazil)



Thanks Luiz
Yes, I have the skills to do that, but I don't fancy spending my time mindlessly resoldering chips hoping it might help :-)
Looks like it's a lost cause...

Thanks
Dave :)

#11

Quote:
Hi
I inherited a 42S and it switches off imediately after switching on. In some cases the display will flash for a split second, in other cases it doesn't show anything. If I press the ON key fast enough I can keep the display on until I release the key.

The self test (ON-LOG) works just fine, and passes OK. But at the end it just switches off. ON-ROOT (the reset function?) works and very briefly display "Machine Reset"

I can even adjust the contrast, and even get it to do calculations if I press a key fast enough at power on, but it switches back off again as before.

Anyone know what is wrong? Is there any higher level reset function I can try?

The batteries are brand new and tested.

Thanks
Dave :)



Ok, I've managed to get the unit open, and what an effort it was!
I drilled out the tabs in the battery compartment and then "snapped" the lower tabs off with the aid of screwdriver, I couldn't do it by hand. Very difficult and touchy procedure.
Here is an inside shot:
http://alternatezone.com/stuff/HP42SinsideCrop.jpg

Anyone notice anything out of the ordinary?

I have soldered the metal tabs to the PCB in case they weren't making contact, no difference.
I have run the unit from a DC supply in case the batteries internal resistance is shot, no difference.
I have replaced the top tantalum cap, no difference.
The bottom cap and diode seem to be part of the dot martix display refresh, remove the cap and the display dims, remove the diode and nothing changes.

It's not the SRAM connections, because as I said it passes all internal memory self tests.

Any ideas?

Thanks
Dave :)



Possibly Related Threads…
Thread Author Replies Views Last Post
  HP 9826A key switches David Ramsey 3 1,314 01-04-2012, 07:29 PM
Last Post: David Ramsey
  42s questions and 42s vs 35s snaggs 13 5,193 09-19-2011, 02:44 AM
Last Post: snaggs
  A new 6-problem challenge (free42 or 42s) Allen 22 5,283 06-12-2011, 05:56 PM
Last Post: Allen
  Hp-42s display problem aj04062 9 2,797 02-27-2011, 08:36 AM
Last Post: aj04062
  HP-42S work-around for sticking to low contrast LCD problem Lyuka 2 1,115 02-01-2010, 01:25 PM
Last Post: DavidShenk
  42s Statistics Problem Norman Dziedzic 11 3,007 12-06-2009, 11:43 PM
Last Post: Thomas Okken
  An HP-42S fix success, and a contrast problem DavidShenk 19 4,351 12-05-2009, 10:17 PM
Last Post: Lyuka
  W&W RAMBOX 64K with DIP-Switches Christoph Giesselink 2 1,141 10-20-2009, 02:14 AM
Last Post: Meindert Kuipers
  HP 42S - Problem Michel Lahcem 13 3,000 08-17-2009, 03:54 PM
Last Post: Michel Lahcem
  Re: 42s Screen problem Alan 0 759 06-06-2007, 02:33 AM
Last Post: Alan

Forum Jump: