HP Forums
Can't seem to flash 30b - Printable Version

+- HP Forums (https://archived.hpcalc.org/museumforum)
+-- Forum: HP Museum Forums (https://archived.hpcalc.org/museumforum/forum-1.html)
+--- Forum: Old HP Forum Archives (https://archived.hpcalc.org/museumforum/forum-2.html)
+--- Thread: Can't seem to flash 30b (/thread-211800.html)



Can't seem to flash 30b - Matt Fegenbush - 02-16-2012

I tried to follow the instructions to erase and flash my 30b, but I fear I may have bricked it. I am running Win XP with a direct serial connection (COM1) and am getting "unable to connect" messages with the MySamba Flash Tool from the sourceforge page.

If someone can enlighten me as to the next step to correct this, I'd sure be appreciative.


Re: Can't seem to flash 30b - Bart (UK) - 02-16-2012

I'm sure it's not bricked, but the flash has been erased. You will not get anything on the LCD at this stage, as the bootloader does not output to it.

It could be that the batteries are drained (the 30b drains the batteries quickly in this "zombie" state) or that there is a bad connection. Try with new batteries and ensure the pogo connector is properly seated.

Regards,
Bart


Re: Can't seem to flash 30b - David Griffith - 02-16-2012

Try all the other com ports that show up. When I did this, I wound up needing to use COM8.


Re: Can't seem to flash 30b - Matt Fegenbush - 02-16-2012

COM1 and COM3 are the only ports that are listed. Both have same result.

New batteries did not change the result.


Re: Can't seem to flash 30b - Bart (UK) - 02-16-2012

Were you sure to press the calculator ON button after erasing & before connecting with Samba?


Re: Can't seem to flash 30b - bill platt - 02-16-2012

So basketballs aren't the only things that can be "bricked?"


Re: Can't seem to flash 30b - Eric Rechlin - 02-16-2012

I don't know, but I will say that the 30b cannot be bricked, so I can't help your argument.

Eric


Re: Can't seem to flash 30b - pascal_meheut - 02-16-2012

Here is what I do when it happens:

I follow the whole procedure again, erase, reset, etc
I launch the SAM-BA program, the Atmel one.

It usually connects. Then I quit and launch MySamba and use it to flash.




Re: Can't seem to flash 30b - Bart (UK) - 02-16-2012

Admittedly, I use the Atmel Samba to flash and have never used MySamba.


Re: Can't seem to flash 30b - Marcus von Cube, Germany - 02-16-2012

Both work but MySamba is much quicker and less picky with the serial adapter.

To Matt: Pressing ON after inserting batteries or pressing RESET is essential!


Re: Can't seem to flash 30b - Alexander Oestert - 02-16-2012

If I remember correctly I had this situation once. It only worked when I removed the batteries from the 30b, reinserted them and started the whole procedure from the beginning: connecting the cable, pressing buttons on the cable and the 30b, starting programs exactly as described, even as the display of the 30b didn't display anything.
I only use Atmel's SAM-BA, not MySamba.


Edited: 16 Feb 2012, 12:36 p.m.


Re: Can't seem to flash 30b - Matt Fegenbush - 02-16-2012

I have been able to sporadically achieve a new error (using SAM-BA v2.11):

TIME OUT
The applet did not return
Please check the connection and reconnect the target device.


Re: Can't seem to flash 30b - Jim P - 02-16-2012

I had a similar problem when trying to use a serial port in a docked computer (where the serial port was on the dock rather than attached to the computer itself.) Changing to a computer with a native serial port solved this. Don't know if this is of any use but there you go.


Re: Can't seem to flash 30b - Matt Fegenbush - 02-16-2012

I am working with a docked laptop. I will try on a desktop with a serial port as soon as I can find one.


Re: Can't seem to flash 30b - Matt Fegenbush - 02-16-2012

Ok, that seemed to be the problem. All is well now. Thank you all for your help.