HP Forums
3421A voltmeter drifts up when open circuit - Printable Version

+- HP Forums (https://archived.hpcalc.org/museumforum)
+-- Forum: HP Museum Forums (https://archived.hpcalc.org/museumforum/forum-1.html)
+--- Forum: Old HP Forum Archives (https://archived.hpcalc.org/museumforum/forum-2.html)
+--- Thread: 3421A voltmeter drifts up when open circuit (/thread-14084.html)

3421A voltmeter drifts up when open circuit - Ellis Easley - 01-10-2002

Do other 3421A users see this behavior? (Or users of other high impedance voltmeters?)

If the unit is set to DC volts, autorange with the input open circuit, and the controller asks for readings over and over, the unit returns readings that slowly increase from 0 to .3V, then it switches to the 3V range where the readings continue to increase until the unit switches to the 30V range. At this point, because of the lower input resistance (10 Mohm), the voltage drops to near zero and so the unit switches back to the .3V range and starts over. It does this even with no mux installed and the internal harness unplugged. When I connect a 100Mohm resistor (the largest I have - I don't even know how close it is because I can't measure it!) to the front panel jacks, the unit reads zero all the time. BTW, if the unit is set to .3V or 3V (not autorange), the reading rises to overrange and stays there.

My theory is that this is caused by leakage from the coils of the relays that route the signals on the main board. The coils are all connected to +5V and the other ends are switched to ground to actuate them (they are the same latching relays that used are on the mux board). The specified input resistance of the voltmeter is 10 Gohm (10^10 ohms!) on the two low ranges and I imagine the input capacitance is being charged from +5V through the leakage resistance of the relays. I think this is the kind of leakage that is supposed to be avoided by the "guarding" techniques recommended in app notes for high input impedance amplifier ICs. The relays probably don't have any provision for guarding (would require an extra pin to be connected to the guarding potential).

If I ever get very brave I might try to isolate the relays from +5V to test my theory (since they are latching relays they don't need power to stay in their current state).

Re: 3421A voltmeter drifts up when open circuit - Yani - 01-11-2002


I built a FET input multimeter using a very nice multimeter movement I salvaged from a home built VTVM. The problem was I used a phenolic PCB which was partially porus and as it absorbet moisture a stray voltage leaked into the the gates of the FETs. As I dried out the board the meter stabilised.

This was about twenty years ago when fibreglass was not as prolific as it is today. I replaced the PCB with a fibreglass board and no more problems.

It could be dust, a porous PCB, damaged transistors (I am not familiar whith this model - is it VT or FET?). There is probably some leaky voltage (current) somewhere.

Re: 3421A voltmeter drifts up when open circuit - Ellis Easley - 01-11-2002

The active input circuitry is a hybrid, probably CMOS, but before it gets there the signal passes through some DIP relays that select the voltage range. This is a low cost (for HP) instrument from around 1982 that has the distinction of using HPIL to connect to a controller. It measures DC volts, AC volts, resistance (2 wire or 4 wire), frequency (to a very limited extent), and has firmware to read T-type thermocouples directly. It can hold option boards which provide a relay multiplexer or digital I/O. It has no display of its own. HP also made a multimeter with front panel controls and display (3468A/B) with similar measurement capability (plus internal current measuring shunts) and HPIL.

Re: 3421A voltmeter drifts up when open circuit - Peter Petersson (Germany) - 01-11-2002

I have seen similar behavior on my HP 3468A Multimeter.
It seems to use the same A/D converter as the 3421A.
Should be no problem because You will never get anything
to measure with a resistance near the input resistance of
the 3421A.

Re: 3421A voltmeter drifts up when open circuit - Tony Duell - 01-11-2002

I've never taken enough readings to look for a trend, but my 3421 certainly drifts (or picks up noise, as I said I've not taken enough readings to say which) when the input is open-circuit. Most very high impedance voltmeters do.
As soon as you connect a source with a sensible restance to the input, then the readings become stable. And since I only ever use it for measuring such sources, it doesn't worry me.

Re: 3421A voltmeter drifts up when open circuit - Ellis Easley - 01-13-2002

Thanks for the feedback. It makes me more confident in the instrument, which is the best meter I have. Since it generally agrees with my other meters, I'm considering it to be "in calibration", I even managed to replace the lithium backup battery without losing the calibration by hooking up a bench supply during the operation.