HP Forums

I tested the program. It works in the two ways.

Id est sending and receiving HP-41 programs via HP82164A.

For instance, this one:

LBL'TEST

'TEST OK

AVIEW

RTN

TEST.DAT:

0015C000F50054455354F754455354204F4B7E85C8022DF5

But I had problems to send programs previously saved

with the following configuration:

HP-41 (HP-IL & X-I/O) -> HP82169A HP-IL/HP-IB -> HP82335A HP-IB/PC card.

I used HP softwares & libraries made for the previous card.

All programs were saved under 'program name.BIN'

Thus CONFIG ( is APPEND)

01 LBL "CONFIG"

 02 7 E-3

 03 LBL 00

 04 CF IND X

 05 ISG X

 06 GTO 00

 07 "PAGE DEBUT?"

 08 PROMPT

 09 GTO IND X

 10 LBL 07

 11 SF 00

 12 SF 01

 13 SF 02

 14 GTO 06

 15 LBL 11

 16 SF 01

 17 LBL 09

 18 SF 00

 19 GTO 08

 20 LBL 14

 21 SF 01

 22 LBL 12

 23 SF 02

 24 SF 03

 25 GTO 06

 26 LBL 10

 27 SF 01

 28 GTO 08

 29 LBL 15

 30 SF 01

 31 LBL 13

 32 SF 00

 33 LBL 08

 34 SF 03

 35 LBL 06

 36 "TAILLE?"

 37 PROMPT

 38 CLA

 39 FIX 0

 40 CF 28

 41 CF 29

 42 ARCL X

 43 ASTO X

 44 SF 25

 45 GTO IND X

 46 GTO 06

 47 LBL "8"

 48 SF 06

 49 SF 05

 50 LBL "4"

 51 SF 07

 52 GTO 05

 53 LBL "16"

 54 SF 06

 55 SF 05

 56 SF 04

 57 LBL 05

 58 CLA

 59 2,6350741

 60 LBL 04

 61 FS? IND X

 62 "*"

 63 FC? IND X

 64 "-"

 65 FRC

 66 10

 67 *

 68 X0?

 69 GTO 04

 70 AVIEW

 71 END

was saved under 'CONFIG.BIN':

00B6C000F700434F4E46494700171B1C1301A9F39673B181FB50414745

2044454255543F8EAE7308A800A801A802B7000CA8010AA800B9000FA8

010DA802A803B7000BA801B900CF0FA8010EA80009A80307F75441494C

4C453F8E879C00A91CA91D9B739A73A819AE73B700C20FF20038A806A8

05C401F20034A807B651C401F3003136A806A805A804068700121A1613

1510171411000000000005ACF3F27F2AADF3F27F2D690011104264B5D2

7E000000000000CC072DF9

I renamed it 'CONFIG.DAT' and tested it.

I got 'READ ERR' when 'CONFIG, XEQ'INP on HP-41?!

However the codes used are the same, aren't they?

Please advice. Thanks.

hi emmanuel,
i just copied and pasted the DAT stream from your above posting into my text editor. then i removed the six linebreaks to get one long line of hex numbers. then i added a line break at the end of the hex numbers (right after the 2DF9). then i saved it as "CONFIG.DAT" . reading the program back to an HP-41C through HPILCOM was no problem. maybe, you should check two things: 1) there *must* be a line break at the end of the data. 2) no line breaks are allowed in the data.

hope, this helps

cheers, hans

Sehr Hans,

Alles in Ordnung. Schön.

Danke. Grüsse.

Emmanuel